manualshive.com logo in svg

Wacker Neuson BFS 1345, Operator'S Manual

Share
Download
Wacker Neuson BFS 1345 Operator'S Manual Download Page 24

Operation

T01110en.fm

24

6.9

Checking the motor before starting

6.9.1

Engine oil
Switch off the engine.
Prior to checking the engine oil level or refilling engine oil, make sure
that the engine bolting level is aligned horizontally.

∗

Remove the oil filler cap (oil level indicator).

∗

If the oil level is below the lower filling mark on the dip stick, add suit-
able engine oil until the oil reaches the edge of the filler neck.

∗

An oil change is required if the engine oil is dirty.

∗

Only use high-quality engine oil, see 

Technical Data

.

The engine is automatically switched off when the oil level falls below
a specific level. If this is the case, the engine can only be started after
engine oil has been refilled.

6.9.2

Fuel
Do not smoke during refueling and make sure that there are no open
flames or sparks in the immediate vicinity.

∗

Turn off the engine and open the fuel tank cap.

∗

Only use leadfree fuel.

∗

Close the fuel tap before the fuel tank is filled with fuel.

∗

Always use the fuel filter when refilling fuel.

∗

Wipe off any spilled fuel before starting the engine.

Oil level
indicator

Upper level mark

Lower level mark

Summary of Contents for BFS 1345











































Reviews:

No comments

Brands by name

Popular brands

Load more brands