manualshive.com logo in svg

Wacker Neuson BFS 1345, Operator'S Manual

Share
Download
Wacker Neuson BFS 1345 Operator'S Manual Download Page 14

Description

T01067en.fm

14

4.3

Functional description

The floor saw must only be operated in a forward direction (see arrow).
The drive motor (1) attached to the frame drives the cutting blade via
the belt (2).
The cutting blade can be infinitely adjusted by means of a crank
handle (3), 1 turn corresponds to a cutting depth adjustment of 5 mm.
The cutting blade guard (4) can be swiveled upwards to make it easier
to assemble and disassemble the cutting blade.
Furthermore, the cutting blade guard can be connected with the water
tank by means of a hose (5) and an adapter.
Wetting the cutting blade with water prevents dust from developing.
The adapter on the water hose allows the connection of an external
water supply.
The drive motor speed can be infinitely adjusted by means of the gas
throttle lever (6), whereby the optimum cutting blade speed is reached
when the drive motor is operated at full throttle.
To facilitate the starting procedure, the drive motor is equipped with a
choke.

Summary of Contents for BFS 1345











































Reviews:

No comments

Brands by name

Popular brands

Load more brands