Vzense DCAM500 User Manual Download Page 25

Page: 25 / 36

each other.

7.2

Range Customization

By default, there are 3 different range modes calibrated for DCAM500, please see

below table for more information:

Range number

Distance range

Range 0

0.35m~1.5m

Range 2

0.8m~4.4m

Range 5

1.2m~6.2m

Please do NOT use uncalibrated modes, the measurement data will not be

guaranteed.

If you need other range mode requirement, you can ask Vzense team to do range

customization, reasonable NRE fee will be charged.

One range mode of the Vzense DCAM500 camera can fulfill furthest distance be at

most 5 times to nearest distance. For example, if the near limitation is 0.4m, then the

furthest distance in this mode can reach about 2m.

7.3

Wide Dynamic Range

As mentioned above, Most of the ToF based 3D sensing technology has range

limitation to nearest and furthest distance, due to the sensor saturation of weak light

strength to far objects. One range mode of the Vzense DCAM500 camera can fulfill

furthest distance be at most 5 times to nearest distance. For example, if the near

limitation is 0.4m, then the furthest distance in this mode can reach about 2m.

Wide dynamic range means that the camera can work at more than one range modes

0.005

0.01

0.015

0.02

0.025

250

400

600

800

1000

1200

1400

1600

1800

2000

2200

2400

2600

2800

3000

3200

3400

3600

3800

4000

4200

ISTA

ERR

DISTANCE RANGE UNIT MM

Summary of Contents for DCAM500





































Search results

Summary of Contents for DCAM500

Reviews:

Related manuals for DCAM500

Brands by name

Popular brands

Vzense DCAM500, User Manual

Search results

Summary of Contents for DCAM500

Reviews:

Related manuals for DCAM500

Brands by name

Popular brands