VYKING FORCE VF3000P Instruction Manual Download Page 24

Page: 24 / 44

Troubleshooting

ISSUE

POSSIBLE CAUSES

CORRECTIVE ACTION

Pump does not reach

working pressure

Nozzle worn

Replace nozzle

Water filter fouled

Clean filter

Insufficient water supply

Turn on water supply tap

fully

Air being sucked into

system

Check tightness of hose

fittings

Air in pump

Switch off the appliance

and keep depressing and

releasing the gun trigger

until the water comes out

in a steady flow. Switch the

appliance back on again.

Adjustable nozzle not

positioned correctly

Adjust the nozzle and make

sure it clicks

Thermostatic valve tripped

Wait for correct water

temperature to be restored

Water being sucked from

an open container from a

height of more than 0.5m

Reduce the suction height

Pump pressure drops

suddenly during use

Water being sucked from

an external tank

Connect appliance to the

mains water supply

Inlet water too hot

Reduce temperature

Nozzle clogged

Clean nozzle with supplied

Inlet filter fouled

Clean filter

Water leakages

Seals worn

Have the seals replaced

at your nearest Authorised

Service Centre

Safety valve tripped and

discharging

Contact an Authorised

Service Centre

Appliance noisy

Water too hot

Reduce temperature (see

specs)

Summary of Contents for VF3000P













































Search results

Summary of Contents for VF3000P

Reviews:

Related manuals for VF3000P

Brands by name

Popular brands

VYKING FORCE VF3000P, Instruction Manual

Search results

Summary of Contents for VF3000P

Reviews:

Related manuals for VF3000P

Brands by name

Popular brands