VWR symphony 5.3 A Operating Instructions Manual Download Page 55

Page: 55 / 68

Operating Instructions | symphony 5.3 A – 06/2009

Maintenance

10.4 Temperature calibration procedure

Temperature calibration steps

1. Activate calibration:



Keep the



key depressed for 5 seconds.



All operating panel indicators flash.

2. Indicate the nominal value:



Press the



key.



The preset value of 37 °C is displayed.

3. Enter the measured value (destination value):



Press the





keys.



Press the





keys.



Destination value e.g. 36.4 °C

4. Accept the destination value:



Press the



key.



The temperature display momentarily shows “CAL”,



Then the corrected actual value (measured destination value
36.4 °C) is displayed.

5. Cancel the calibration process:



Press any key.



The temperature display and the CO

display show the actual

values.

Summary of Contents for symphony 5.3 A





































































Search results

Summary of Contents for symphony 5.3 A

Reviews:

Related manuals for symphony 5.3 A

Brands by name

Popular brands

VWR symphony 5.3 A, Operating Instructions Manual

Search results

Summary of Contents for symphony 5.3 A

Reviews:

Related manuals for symphony 5.3 A

Brands by name

Popular brands