background image

Gel Imagers 

 

 

System Specifications 

 

Configurations 

Part No. 

Description 

89131-380

 

Gel Imager, 0.3 Camera, 20 x 20cm Transilluminator, 302nm UV, 115V

 

89131-382

 

Gel Imager, 0.3 Camera, 20 x 20cm Transilluminator, 302nm UV, 230V

 

89131-384

 

Gel Imager, 0.3 Camera, 21 x 26cm Transilluminator, 302nm UV, 115V 

89131-386

 

Gel Imager, 0.3 Camera, 21 x 26cm Transilluminator, 302nm UV, 230V

 

89131-388

 

Gel Imager, 0.3 Camera, 20 x 20cm Transilluminator, 302/365nm UV, 115V

 

89131-390 

Gel Imager, 0.3 Camera, 20 x 20cm Transilluminator, 302/365nm UV, 230V 

89131-392 

Gel Imager, 0.3 Camera, 21 x 26cm Transilluminator, 302/365nm UV, 115V 

89131-394 

Gel Imager, 0.3 Camera, 21 x 26cm Transilluminator, 302/365nm UV, 230V 

 

 

89131-396 

Gel Imager Plus, 1.3 Camera, 20 x 20cm Transilluminator, 302nm UV, 115V 

89131-398 

Gel Imager Plus, 1.3 Camera, 20 x 20cm Transilluminator, 302nm UV, 230V 

89131-400 

Gel Imager Plus, 1.3 Camera, 21 x 26cm Transilluminator, 302nm UV, 115V 

89131-402 

Gel Imager Plus, 1.3 Camera, 21 x 26cm Transilluminator, 302nm UV, 230V 

89131-404 

Gel Imager Plus, 1.3 Camera, 20 x 20cm Transilluminator, 302/365nm UV, 115V 

89131-406 

Gel Imager Plus, 1.3 Camera, 20 x 20cm Transilluminator, 302/365nm UV, 230V 

89131-408 

Gel Imager Plus, 1.3 Camera, 21 x 26cm Transilluminator, 302/365nm UV, 115V 

89131-410 

Gel Imager Plus, 1.3 Camera, 21 x 26cm Transilluminator, 302/365nm UV, 230V 

 
 

Camera  

System will be configured with one of the two camera 
options: 

1.3mpx (high resolution) or 0.3mpx .   

 
Both cameras use a USB 2.0 PC connection.  All camera 
settings are factory pre-set for optimum performance when 
viewing gels, films, or membranes under low light level 
conditions. UVP Technical Support should be contacted 
before making any adjustments to the camera settings. 

 

Lens  

The Gel Imager Plus with the 1.3mpx camera is equipped 
with an 8-48mm zoom lens fitted with a close-up diopter and 
step-up ring.  The camera can then be held in a fixed 
position.  The diopter is for focusing on objects at the focus 
length of the Gel Imager.   
 
The Gel Imager with the 0.3mpx camera is equipped with a 
5.7-34.2mm zoom lens fitted with a close-up diopter and 
step-up ring. The camera can then be held in a fixed 
position.  The diopter is for focusing on objects at the focus 

 

Summary of Contents for 89131-380













Reviews: