background image

VWR International, LLC., Stereo Zoom Microscope                                     

 

Safety Instructions 

 

Please read this manual carefully before using this product for optimal use.  The indicated cautions are 

related to safety and you should observe all safety and warning instructions to avoid potential damage 

to product and injury to operators.  Keep this manual for future reference. 

 

Note: Use this product only in a way described in the product literature and this manual.  Before using 

the product, verify that this product is suitable for its intended use. 

 

Do not modify the system components or use the unauthorized parts as this will void the product 

warranty. 

  

The following warning labels (or symbols) are found on the microscope, Study the meaning of the 

warning labels (or symbols) and always use the equipment in the safest possible manner. 

                           

Warning Label / Symbol 

Explanation 

 

Indicates that the surface becomes hot, and 
should not be touched with bare hands.

 

 

Indicates that the main switch is ON.

 

 

Indicates that the main switch is OFF.

 

~

 

Indicates alternating current. 

 

 

Summary of Contents for 89404-492












Reviews: