manualshive.com logo in svg

VP Networks MultiAP 700G, User Manual

Share
Download
VP Networks MultiAP 700G User Manual Download Page 7

 

 

 

Tunnel Netmask 

This shows the subnet mask acquired in the established tunnel. 

 

Firmware / Flash  

Firmware Version 

This shows the firmware version loaded into the flash partitions. 

Flash Status 

This shows the firmware status on the flash partitions. 

Boot from 

This indicates which flash partition boots up the system. 

Firmware Upgrade 

Target 

This shows which flash partition is used for firmware upgrade. 

 

4.2  Wireless 

 

Wireless Information 

Name 

This shows the system name defined in previous section. 

Number of WLANs 

This shows number of added SSIDs. 

Current Clients 

This indicates the number of associated clients. 

Current Channel 

This shows which 802.11 channel the system is using. 

Current Status 

This shows the current status of the device. 

 

Connected Clients 

Manufacturer 

This shows the manufacturer based on the MAC prefix. 

MAC address 

This shows the client MAC address. 

WLAN SSID 

This shows which SSID the client is associated. 

VID 

This shows the VLAN ID used on the SSID. 

Type 

This shows the radio mode of the client. 

Authentication 

This shows the client authentication. 

Status 

This shows the association status and the associated duration. 

Details 

This links to the detailed page of each client. 

 

For information about the Clients Details, please refer to section 5.2. 

Comment: 

? any other than On? 

Summary of Contents for MultiAP 700G











































Reviews:

No comments

Brands by name

Popular brands

Load more brands