manualshive.com logo in svg

VP Networks MultiAP 700G, User Manual

Share
Download
VP Networks MultiAP 700G User Manual Download Page 12

 

 

 

5.1.2 

L2TP Tunnel Settings 

 

L2TP Tunnel Settings 

L2TP Tunnel 

Enabling L2TP option on the system would start the tunnel establishment from 
the access point to the server for centralized traffic management. 

L2TP Server 

Address 

This specifies the L2TP server IP address for the access point to connect to. 

L2TP/PPP 

Username 

This specifies the L2TP/PPP Username for tunnel authentication purpose. 

L2TP/PPP Password 

This specifies the L2TP/PPP Password for tunnel authentication purpose. 

Tunnel IP Address 

This specifies the unique IP address for the MultiAP 700G unit to communicate 
over the tunnel.  

If 

From DHCP

 is set, the IP address of the MultiAP 700G unit is then acquired 

from a DHCP server over the tunnel. Tunnel IP Address and Tunnel Subnet 
Mask will be disabled automatically. 

Tunnel Subnet Mask 

This setting specifies the subnet mask of the MultiAP 700G unit over the 
tunnel. 

Tunnel Management 

VLAN 

This specifies the VLAN from which management sessions are allowed over 
the tunnel.  The establishment of management sessions is restricted only to 
the specified VLAN ID.  If 

Management VLAN ID

 is set to zero, no VLAN 

restriction is applied.   

The default value of this setting is 

zero

.  It means no tagging is enabled 

(instead of tagged with zero). 

 

Summary of Contents for MultiAP 700G











































Reviews:

No comments

Brands by name

Popular brands

Load more brands