manualshive.com logo in svg

VP Networks MultiAP 700G, User Manual

Share
Download
VP Networks MultiAP 700G User Manual Download Page 27

 

 

 

ACK Timeout 

This setting provides the option to set the wait time to receive 
acknowledgement packet before doing retransmission. 

CTS Timeout 

This setting provides the option to specify the timeout for the unit to wait for 
CTS response in the RTS/CTS handshake. 

802.11g Protection 

When this option is enabled, 802.11g devices would be in favor in mixed mode 
(11g and 11b) networks. 

Preamble Type 

Preamble Type defines the length of the CRC block for communication 
between the AP device and adapters. Available options are 

Long

 and 

Auto

. A 

long preamble type can be selected if the device is operating in a ‘noisy’ 
network environment. 

By default, it is set as 

Auto

. 

 

5.3.2 

Neighbor AP Discovery 

 

Neighbor AP Discovery 

Neighbor AP 

Discovery 

Check the box to enable the function of scanning neighbor APs. 

Scanning Interval 

This setting determines how often the access point goes to other channels to 
discover Neighbor AP. 

Scanning Time 

This setting determines how long the access point stays on the other channels 
to discover Neighbor AP. 

 

5.3.3 

Ethernet Settings 

 

Ethernet Settings 

Speed 

This setting provides the option to set the speed of the Ethernet. 

 

Comment: 

 

Summary of Contents for MultiAP 700G











































Reviews:

No comments

Brands by name

Popular brands

Load more brands