“Modbus” function
The appliance is accessible from a network using
Modbus protocol, connected via a serial port that must
be configured appropriately by the installer. With this
connection, certain operating parameters of the
appliance can be controlled or displayed remotely.
Where the appliance is wired into a "domotic" system,
the appliance will be able to communicate with the rest
of the network. The cable needed for this connection is
supplied with the product.
Maintenance/Cleaning
Before commencing any servicing operation, make
certain that the appliance is disconnected from the
power supply. Dismantling and assembly are special
maintenance operations and must be entrusted to
professional technicians.
Filters
Recommended maintenance intervals:
Because levels of air pollution depend typically on
geographical location and are variable, the life of the
filters will be similarly variable. With this general
consideration in mind, the following maintenance
intervals are recommended:
Models One
:
Inspect filters: every 50/60 days;
replace filters: every 4 to 6 months.
Model One F
:
Inspect filters: every 50/60 days;
replace filters: every 4 to 6 months. With this model, the
system automatically displays an early warning message
on the control panel, at around x-2 months after a new
filter is fitted, and at the end of x months, an alarm
message causing the appliance to lock up. The system
can be reactivated by resetting the error on the control
panel, or simply by fitting new filters. The installer must
set value x (minimum 4, maximum 6) when the system is
first put into operation.
N.B. Failure to clean or replace filters can seriously affect
the efficiency of the system, causing:
- higher pressure losses in the air circuit and lower air
flow rate;
- consequently, a reduction in performance of the
appliance, and less comfortable room conditions.
N.B. Clogged air filters are the most frequent cause of
the appliance locking up (error code ERR10).
Important information concerning
the environmentally compatible
disposal
IN CERTAIN EUROPEAN UNION COUNTRIES THIS
PRODUCT
DOES
NOT
FALL
WITHIN
THE
REQUIREMENTS
OF
THE
NATIONAL
LAWS
IMPLEMENTING DIRECTIVE WEEE, AND IN THESE
COUNTRIES THE PRODUCT IS NOT SUBJECT TO
SEPARATE DISPOSAL OPERATIONS AT THE END OF
ITS WORKING LIFE.
This product conforms to EU Directive 2012/19/EC.
This appliance bears the symbol of the
barred waste bin. This indicates that, at
the end of its useful life, it must not be
disposed of as domestic waste, but must
be taken to a collection centre for waste
electrical and electronic equipment, or
returned to a retailer on purchase of a replacement.
It is the user's responsibility to dispose of this appliance
through the appropriate channels at the end of its useful
life. Failure to do so may incur the penalties established
by laws governing waste disposal.
Proper differential collection, and the subsequent
recycling, processing and environmentally compatible
disposal of waste equipment avoids unnecessary
damage to the environment and possible related
healthrisks, and also promotes recycling of the materials
used in the appliance.
For further information on waste collection and disposal,
contact your local waste disposal service, or the shop
from which you purchased the appliance.
Manufacturers and importers fulfil their responsibilities
for recycling, processing and environmentally compatible
disposal either directly or by participating in collective
systems.
ENGLISH
26
2
26
GRAY
BLACK
WHITE
BLACK: -
WHITE: +
GREY: G
26
Summary of Contents for HRI-E ONE
