background image

911352_00(5)  Page 1  of 8

C

C

LA

SSIFIE

D

C

LA

SSIFIE

D

Installation Instructions – Electrical

CX33A/35A &CX98/99              Device

GENERAL INFORMATION

ELECTRICAL SPECIFICATIONS

Voltage ............................................................... 24 VDC
Current ............................................................... 0.4 A
Current on arming ........................................... 300-mS 16-A in-rush
External alarm dry contacts (NO and C) .... 24 VDC, 1 A rating
Normally closed inputs .................................. Fire alarm (FA; required)

External inhibit (EI)
Door position switch (DPS)

The Von Duprin Chexit

 

device is designed for accident hazard or fire exit applications. It meets both life

safety and security needs as well as all requirements of NFPA101   for “Special Locking Arrangement” and
UBC “Special Egress-Control Devices.”

The Von Duprin Chexit

 

device sounds an alarm and keeps an exit door secured for 15 seconds following an

attempt to exit. The Chexit releases immediately upon a fire alarm condition.

®

PUSH UNTIL ALARM SOUNDS

DOOR CAN BE OPENED

IN 15 SECONDS

CX Rim Exit Device

(CX98/99 shown)

Chexit Module

 Cable

Door Sign

TM

THE

®

Do not exceed rated

specifications.

WARNING

!

The Chexit device must be

installed in accordance

with these instructions by

a qualified electrician.

WARNING

!

Wiring must be in

accordance with all local

codes and regulations.

WARNING

!

VON DUPRIN

®

911352-00

Summary of Contents for Chexit CX33A/35A









Reviews: