Von Duprin 3350AWDC Installation Instructions Manual Download Page 15

Page: 15 / 16

TOP STRIKE AND COVERS

Adjust top strike as necessary, then install the third
strike screw to fi x the strike position.

Metal

Wood

#25 x

³⁄₄

" Deep

#10-24

¹⁄₈

" Drill

Pilot 1" Deep

(metal)

(wood)

For fi re devices, prepare door edge and cover plate.

Fire application only

Intumescent must be properly aligned before exposed
adhesive contacts cover plate. Adhesive is permanent and
not repositionable.

³⁄₁₆

" Drill, Pilot 1" Deep x2

Insert plastic
anchors

Peel adhesive backing from
intumescent and apply to
back side of cover plate

b-1

b-2

Install cover plate to door edge, then completely
tighten down center case screws.

For non-fire devices, first
prepare door edge

¹⁄₈

" Drill, Pilot 1" Deep x2

c-2

c-1

Install center case cover.

Remove protective
film from pushbar

Summary of Contents for 3350AWDC

















Search results

Summary of Contents for 3350AWDC

Reviews:

Related manuals for 3350AWDC

Brands by name

Popular brands

Von Duprin 3350AWDC, Installation Instructions Manual

Search results

Summary of Contents for 3350AWDC

Reviews:

Related manuals for 3350AWDC

Brands by name

Popular brands