Volvo Penta TAMD74A Operator'S Manual Download Page 54 | Manualshive

Page: 54 / 76

background image

52

Maintenance: Electrical system

Electrical system

The engines are equipped with a bi-polar electrical system with alternating current generator. System voltage is
12 alternativly 24 V.

WARNING! Before starting work on the electrical system, the engine must be stopped and the powered
turned off with the main switch/switches. Shore power to the engine heater, battery charger or other extra
equipment fitted on the engine must be disconnected.

Main switches

The main switches must never be turned off until the
engine has been stopped. Breaking the circuit be-
tween the alternator and the batteries while the en-
gine is running can damage the alternator. For the
same reason, the charge circuits must never be
switched while the engine is running.

IMPORTANT! Never turn the power off using
the main switches while the engine is running.

Electrical connections

Make sure electrical connections are tightened, dry
and free from oxide. If necessary, spray these con-
nections with water-repellant (Volvo Penta all-round
oil).

Fuses

Two semi-automatic 8A fuses are located in the main
electric terminal box. Fuses cut the current when
there is an overload and are reset by pressing the
buttons on the side of the main electrical terminal
box. Determine the cause of the overload before re-
setting the fuses.

«
...
52
53
54
55
56
...
»

Summary of Contents for TAMD74A













































































Reviews:

No comments

Related manuals for TAMD74A

UNIVERGE SL2100

Brand: NEC Pages: 196

UNIVERGE SL2100

Brand: NEC Pages: 174

ElectraElite IPK

Brand: NEC Pages: 151

Brand: Waters Pages: 55

Brand: Paradox Pages: 2

Brand: GANTERUD Pages: 24

Brand: QUAD Pages: 17

Brand: fadini Pages: 16

Ecomot300 AC2630

Brand: IFM Electronic Pages: 111

Brand: Uniden Pages: 28

Brand: UniFocus Pages: 23

Brand: UniFocus Pages: 6

Brand: Ziton Pages: 36

Brand: Voltech Pages: 8

Brand: Miller-Leaman Pages: 18

Brand: Hunter Pages: 2

Brand: SMT Pages: 24

Brand: Tektronix Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands