Volvo Penta TAMD74A Operator'S Manual Download Page 19 | Manualshive

Page: 19 / 76

background image

17

Controls

Friction brake

The control is fitted with an adjustable friction brake for
engine speed control.

1. Remove the cover on the control.

2. Set the lever to half acceleration/reverse.

3. Adjust the friction brake. Turn clockwise for stiffer lever

movement and anticlockwise for lighter movement.

4. Refit the cover.

Dual lever control

Manoeuvring

The dual lever control has separate levers for shifting (1)
and engine speed control (2).

Control A has a mechanic detent so that shifting can be
performed only when the engine speed lever is in idle
speed position. A neutral position switch is available that
allows the engine to be started only when the reverse gear
is disengaged.

Black lever (1):
N = Neutral position. Reverse gear disengaged.
F = Reverse gear engaged for moving forwards.
R = Reverse gear engaged for moving backward.

Red lever (2):
Engine speed control.

Friction brake

The controls are fitted with an adjustable friction brake for
engine speed control.

Adjust the friction brake by turning the screw (control A) or
the lever (control B).

Turn clockwise (+) for stiffer lever movement and
anticlockwise (–) for lighter movement.

B

A

2

1

«
...
17
18
19
20
21
...
»

Summary of Contents for TAMD74A













































































Reviews:

No comments

Related manuals for TAMD74A

Brand: ABB Pages: 138

Brand: ABB Pages: 116

Relion 615 series

Brand: ABB Pages: 136

FPBA-01 PROFIBUS DP

Brand: ABB Pages: 2

ControlMaster CM15

Brand: ABB Pages: 4

Brand: Baccara Pages: 16

Brand: eclisse Pages: 40

Brand: ICP DAS USA Pages: 7

I-2533CS Series

Brand: ICP DAS USA Pages: 8

Brand: Jedia Pages: 12

Brand: JED Micro Pages: 10

Brand: JCM Technologies Pages: 2

Brand: Maestra Pages: 22

Brand: Lattice Semiconductor Pages: 2

Brand: Lathem Pages: 4

Brand: tams elektronik Pages: 36

Brand: National Instruments Pages: 40

Brand: National Instruments Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands