Volvo Penta D5 Operator'S Manual Download Page 43 | Manualshive

Page: 43 / 80

background image

Drive belt, check and change

WARNING!

Stop the engine before doing any maintenance work.

Check

Check belt tension and condition regularly. If the belt
is too tight it can damage bearings and if it is too loose
it may slip. Check and adjust after operation when the
belt is warm.

IMPORTANT!

Always change a belt, which looks worn or cracked.
Belts which operate in pairs must be changed
together.

Adjust and replace

Adjust and change as necessary. It can generally be
said that the belts are correctly tensioned if they can
be pressed down 10 mm (3/8") by thumb pressure.
Clean the belt grooves before fitting a new belt.

Alternator belt

Adjust

1 Loosen the screw (

5

).

2 Push the alternator belt pulley (4) to the right

until the belt is correctly tensioned.

3 Tighten the screw.

Replace

1 Remove the belt for the fuel pump as described

in “

Coolant pump / Fuel pump, Adjust

”

2 Loosen the screw (

5

).

3 Push the alternator belt pulley (4) to the right

until the correct belt tension is achieved.

4 Tighten the screw (

5

).

5 Replace the belt for the fuel pump and tension

the belt as described in

Coolant pump / Fuel

pump, Adjust

”.

Maintenance

47713336 03-2021 © AB VOLVO PENTA

41

«
...
41
42
43
44
45
...
»

Summary of Contents for D5

















































































Reviews:

No comments

Related manuals for D5

Brand: Kärcher Pages: 224

Brand: FAAC Pages: 22

Brand: Selve Pages: 24

Brand: KYMCO Pages: 244

Brand: Texas Equipment Pages: 38

Brand: Texas Equipment Pages: 57

Brand: Texas Equipment Pages: 60

Brand: Texas Equipment Pages: 44

Brand: aFe Power Pages: 16

Brand: Kärcher Pages: 116

Brand: O.S. engine Pages: 48

Geareducer M1712

Brand: Marley Pages: 8

Brand: Alemlube Pages: 16

ZT-5400 Powertrain

Brand: Hydro-Gear Pages: 48

Brand: Grindmaster Pages: 1

80 - V1.1 ASSEMBLY EXHAUSTS 3211I

Brand: MVVS Pages: 1

45 - V1.1 ASSEMBLY EXHAUSTS 3207S-3208S

Brand: MVVS Pages: 1

Brand: MVVS Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands