Volvo Penta D5 Operator'S Manual Download Page 70

Page: 70 / 80

Lubrication System

Engine

Oil capacity including oil filters, approx.:

No engine inclination

14 liters

23 liters

Oil pressure, hot engine:

Oil pressure during neutral

80 kPa

at operating speed 1100 r/min

450 kPa

Oil quality

(1)

Sulfur content in fuel, by weight

<0,5 %

0,5 – 1,0 %

> 1,0 %

(2)

Oil change interval, reached first in operation:

VDS-3
VDS-2

(4)

ACEA: E7, E5, E3

(3)

API: CI-4, CH-4

500

hours or 12 months

250

hours or 12 months

125

hours or 12 months

Lowest recommended oil grade. Engine oil with higher oil grade is always possible to use.

If sulphur content is > 1.0% by weight, use oil with TBN > 15.

API: CG-4 or CH-4 are acceptable in markets outside Europe, instead of ACEA E3.

(4)

The oil must also comply with at least one of the following specifications: ACEA:E7, ACEA:E5, Global DHD-1,

API:CI-4, API:CH-4.

VDS = Volvo Drain Specification
ACEA = Association des Constructeurs Européenne d'Automobiles
API = American Petroleum Institute
Global DHD = Global Diesel Heavy Duty
TBN = Total Base Number

Viscosity

Select the viscosity according to the table.

The temperature values refer to stable ambient
temperatures.

Technical Data

47713336 03-2021 © AB VOLVO PENTA

Summary of Contents for D5

















































































Search results

Summary of Contents for D5

Reviews:

Related manuals for D5

Brands by name

Popular brands

Volvo Penta D5, Operator'S Manual

Search results

Summary of Contents for D5

Reviews:

Related manuals for D5

Brands by name

Popular brands