manualshive.com logo in svg

Voltech BC-2415P, User Manual, Page: 9 / 12

Share
Download
Voltech BC-2415P User Manual Download Page 9

O.  Specifications 

 

Model 

BC-2415P 

BC-2420P 

BC-2430P 

Output 

Output (Charge) Voltage Selections 

Absorption V 

Float V 

Standby V 

WET 

29.0V 

27.0V 

Float Voltage less 4% 

LiFePO4   

29.2V 

27.2V 

N/a 

LiFePO4 #2 

28.8V 

27.2V 

N/a 

AGM    (Default setting) 

28.8V 

26.4V 

Float Voltage less 4% 

AGM #2 

28.6V 

26.8V 

Float Voltage less 4% 

GEL #2 

28.4V 

27.4V 

Float Voltage less 4% 

CALCIUM 

30.2V 

27.6V 

Float Voltage less 4% 

User Define 1 

  24V - 32V   

User Define 2 

  24V - 32V 

Lead Crystal 

29.4V 

27.2V 

N/a 

Equalization 

  31V 

Maximum Output Charging Current (Continuous) 

15A 

20A 

30A 

Recommended Battery Capacity Range 

(for all battery type) 

6 – 150AH 

8 – 200AH 

10 - 300AH 

Soft Start Bulk Charge 
Battery Voltage to Trigger (cut-in) Soft Start 

Bulk Charge Mode 

<21.0V 

Soft Start Bulk Charge Current (Current Limit) 

1/2 of the charging 

current 

1/2 of the charging 

current 

1/2 of the charging 

current 

 
Ripple and Noise (Peak to Peak) 

<200mV 

<200mV 

<200mV 

Efficiency at Maximum Power (230V) 

>85% 

>85% 

>84% 

 
Dual Bank Charging (Battery must be of same type) 

Yes 

Yes 

Yes 

Input 

AC Voltage Range 

200 – 240V 50Hz~ 

AC Current at Full Load (230V) 

2.5A 

3.5A 

5.0A 

Protection 

Overload 

90-110% Rated Output Current or 50% Rated Output Current (Soft Charge) 

Protection Type : Constant Current Limiting, recovers Automatically after 

Fault Condition is Removed. 

Short Circuit 

Recovers Automatically if Fault Condition is Removed within 20 seconds 

Otherwise the charger will shut down until re-start the charger again 

Reverse Polarity 

Automotive type Blade Fuse 

Over Temperature 

Protection Type: Shut Down 

OVP Output Over Voltage 

Yes 

Cooling 

Cooling Method 

Thermostatic, Variable Speed Fan 

Indicators 

4-Stage Battery Charger   

Yes 

Charge Phase Bulk / Absorption / Float 

Yes 

Fault Mode 

Yes 

Over Temp   

Yes 

Charger ON 

Yes 

Fuses 

AC Fuses at IEC AC Power Socket 

T3.15A 

T4A 

F8A 

DC Car Blade Fuse 

30A 

30A 

25Ax2 

Accessories 

Supplied Accessories 

Remote Temperature sensor, ac cable, spare ac fuse at socket, spare dc 

fuse, CD Software, USB Cable 

Optional Accessory 

Remote Control Panel (Model:HBR-3100) 

Approvals 

Safety :   

CE: EN 60335 

SAA: AS/NZS 60335.1, AS/NZS 60335.2.29 

  (Includes clause 21.102: Vibration Test) 

Yes 

 

EMC: EN 55014; EMF: EN50366 

Yes 

Others 

Dimensions and Weight 

200x80x260mm ; 3.0kg  200x80x260mm ; 3.0kg  200x80x320mm ; 3.9kg 

Remarks 

All values are based on the standard ambient temperature 25°C and pressure 0.1Mpa. 

Summary of Contents for BC-2415P













Reviews:

No comments