manualshive.com logo in svg

VOLKTEK NSH-580, User Manual

Share
Download
VOLKTEK NSH-580 User Manual Download Page 74

VOLKTEK NSH-580 MANAGED 24-PORT 10/100 + 4 G COMBO L3 SWITCH 

Confirm Authentication Key

: Re-type the key entered above.  

NOTE: 

The VLAN of the RADIUS server connected to the switch must be the 

same as the VLAN of the system management interface. 

Click 

Submit

 to save changes to RAM memory. Click

 Refresh

 to view effect of changes. 

To eventually make all the changes permanent in Flash memory, go to the 

Save 

Configuration page

 (bottom of management menu) and click 

Save

.  

 

Radius 
 

7.10.4  IP DHCP Snooping 

In order to filter unwanted DHCP response, you can enable DHCP filtering function to 
allow DHCP response back from the special port(s) where real DHCP server stands. 

To enable this function, go to physical interface configuration page, select ‘Enable’ at 
‘DHCP-Snoop’ item, then click ‘summit’ to apply the global configuration setting. 

 

  

73

Summary of Contents for NSH-580






































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands