Volkswagen golf 2006 Work Description Download Page 50

Page: 50 / 93

- On vehicles with full wheel cover, install cover so that tire
inflating valve is guided through the designated recess

arrow -

Loosen anti-theft wheel bolts and tighten

Note:

The adapter to loosen/tighten the anti-theft wheel
bolts is located with the vehicle tool kit.

If there is no adapter installed in the vehicle for
loosening/tightening the anti-theft wheel bolts, use
master wheel bolt key set T10101 .

In case of losing the adapter, a replacement adapter
can only be obtained via the code number.

The adapters code number for loosening/tightening
the anti-theft wheel bolts is stamped at the face of
the adapter.

Special tools, testers and auxiliary items required

Page 3 / 46

Description of work (part 2 of 2)

Summary of Contents for golf 2006






























































































Search results

Summary of Contents for golf 2006

Reviews:

Related manuals for golf 2006

Brands by name

Popular brands

Volkswagen golf 2006, Work Description

Search results

Summary of Contents for golf 2006

Reviews:

Related manuals for golf 2006

Brands by name

Popular brands