Volkswagen golf 2006 Work Description Download Page 24

Page: 24 / 93

"At MIN-marking and slightly above it"

- 2 -

, "NO

TOPPING OFF REQUIRED" .

Recommended brake fluid level when brake pads
are new or are far removed from the brake pad wear
limit:

"Between MIN- and MAX-Marking" .

Brake system, visual check for leaks and damage

Check the following components for leaks and damage:

Brake master cylinder

Brake booster (on anti-lock braking system:
Hydraulic unit)

Brake pressure regulator and

Brake calipers

- Check that brake hoses are not twisted.

- Turn steering to left stop and to right stop. During this
operation no brake hose must touch any vehicle
components.

- Check brake hoses are not porous or brittle.

- Check brake hoses and pipes for chafing.

- Check brake connections and methods of securing for
correct seating, leaks and corrosion.

Warning!

Page 14 / 37

Description of work (part 1 of 2)

Summary of Contents for golf 2006






























































































Search results

Summary of Contents for golf 2006

Reviews:

Related manuals for golf 2006

Brands by name

Popular brands

Volkswagen golf 2006, Work Description

Search results

Summary of Contents for golf 2006

Reviews:

Related manuals for golf 2006

Brands by name

Popular brands