background image

055 0005

Door Speakers

5

1.

 Pry 

off 

door pull handle cover

.  Remove two  

 

(2) exposed phillips screws from door pull  handle.

2.

 

1998- 2002 models: 

 Remove two (2) Torx   

 

T20 screws from bottom of door panel.

 

2003- models: 

 Remove three (3)

 

Torx T20 screws  

 

from bottom of door panel.

3.

  Pry out bottom and sides of door panel to  

 

release six (6) retaining clips.  Lift door panel  

 

firmly to release.  Disconnect wiring harnesses  

 and 

door release cable

 to remove door panel  

 (Figure 

1).

4.

  Use a drill and 3/8” bit to drill out 

rivets

 

 securing 

speaker assembly

 to door.  Pull out  

 

assembly, disconnect and remove (Figure 2).   

 

Use a nail punch to knock out remains of rivets in  

 mounting 

surface.

5.

  Secure new speaker to speaker adaptor 

 

bracket.  Place speaker/bracket assembly in  

 

location and mark new mounting holes.  Remove  

 

speaker and drill new holes with a 1/8” bit.  

6.

  Connect speaker wiring adaptor of 

 

replacement speaker to vehicle speaker

 

harness.  Secure speaker/bracket assembly  

 

to location (Figure 3).

7.

  Test speaker operation and reinstall door panel  

 

by reversing removal steps.

FIGURE 2

Rivets

Speaker Assembly

Door Pull 
Handle Cover

FIGURE 3

FIGURE 1

Door Release 
Cable

Note:

  

Door panel for 2003- models 

is slightly different in appearance, but 
removal steps are the same as 1998- 
model shown.

1-800-955-9094

TECHNICAL SUPPORT

Always be careful when drilling in a vehicle.  WEAR EYE 
PROTECTION.  Be aware of things such as wiring, windows, 
fuel lines and safety devices.  Check drilling depth and 
location to avoid damage to vehicle appearance.

CAUTION:

!

NOTES:

Please read first

• 

 Instructions show factory size speakers or speakers 
with adaptor brackets only.  Cutting or fabrication (not 
shown) will be required for other speaker sizes.

If vehicle is equipped with Monsoon system, a speaker mounting 
bracket must be fabricated in order to install an aftermarket 
speaker.  An adaptor is available for non-Monsoon applications.

IMPORTANT:

!



Check that wires do not interfere with window operation.

 Test door lock and release operation.

SAFETY CHECK

!

Copyright 2012  Crutchfield Corporation

R

Summary of Contents for Beetle 1998-2010









Reviews: