Volirium Flytec Balloon Live Sensor User Manual Download Page 15

Balloon Live Sensor  

User 

Manual 

Page 15 

Firmware FS.04.17  

 

Date: 2021-05-13 

Balloon Live Sensor. The track recording on the Balloon Live Sensor will be stopped when 
the flight is stopped in the Balloon Live App. 

Note:

  Even  when  the  Balloon  Live  Sensor  was  configured  to  start  track  recording 

automatically, it will not start a new track recording after the Balloon Live App has sent the 
end of flight command. To start a new recording, either the flight needs to be started in the 
app or track recording needs to be activated using the button on the device. 

The device can be set into three track recording modes: 

1. 

Start track recording automatically when a takeoff has been detected, stop the track 
recording again after a landing has been detected (factory default setting). 

2. 

Start track recording immediately after turning on the device. 

3. 

Do not start track recording after turning on the device. Manual start is available. 

In the automatic track recording mode, the takeoff is determined by a position or altitude 
change exceeding a threshold, while the landing is determined when both the position and 
altitude remain unchanged over a period of 60 seconds. Due to the nature of how balloons 
often move in slow winds, the automatic mode may fail to start a track recording properly or 
may stop it early. 

The track recording start/stop mode as well as the interval in which GPS positions are stored 
can be set by long pressing the OK/mode/config 

 button for about 3s. The current start 

mode  and  interval  will  be  displayed  and  start  flashing  to  indicate  that  they  can  now  be 
adjusted with the Selection up 

 or the Selection down 

 buttons. The selection buttons 

will move through the available  recording intervals and then switch to the next  start/stop 
mode after the last available interval value in the current start/stop mode.  

Mode  Description 

Recording intervals 

Manual start/stop of track recording 

1s, 2s, 3s, 5s, 10s, 30s 

Immediate track recording after turning on device 

1s, 2s, 3s, 5s, 10s, 30s 

Automatic start/stop of track recording 

1s, 2s, 3s, 5s, 10s, 30s 

 

 

 

 

Summary of Contents for Flytec Balloon Live Sensor





























Reviews: