VOIspeed V-IP400P User Manual Download Page 36

Page: 36 / 37

VOI

SPEED

SER

ANUAL

6.8.3 -

Syslog (Syslog Config)

In this section you can define a ‘syslog’ server storing all log files for the phone. This

function should be enabled only if the system is not working correctly or if there was an

explicit request from VOIspeed technical support team (tick

Enable Syslog

checkbox).

When this function is enabled, you need to have an active syslog server connected to the

same network on which you have connected the V-IP400P.

You will need to enter the following details:

•

Syslog server’s IP address.

•

UDP port used by the server (default value: 514).

•

MGR log (0..7) to set the level of details of the phone’s log files.

•

SIP log (0..7) to set the level of details of the log files relating to SIP traffic.

6.8.4 -

Time Setting (Time Set)

Manual Timeset

you can manually setup the system’s time and date.

Alternatively, in

SNTP Timeset

you can enter the details of a network NTP server that

will be responsible for automatically update the phone’s time and date.

Summary of Contents for V-IP400P






































Search results

Summary of Contents for V-IP400P

Reviews:

Related manuals for V-IP400P

Brands by name

Popular brands

VOIspeed V-IP400P, User Manual

Search results

Summary of Contents for V-IP400P

Reviews:

Related manuals for V-IP400P

Brands by name

Popular brands