manualshive.com logo in svg

Vogelsang FX116, Operating Instructions Manual

Share
Download
Vogelsang FX116 Operating Instructions Manual Download Page 6

User informa tion  

 

 

6

 

WBV.PU.003.EN FX116 V1.0

 

 

 

 

 

1.3 

Explanation of symbols 

The following symbols and signal words are used in this manual: 
 

 

 

1

 

If personal protective equipment is needed to work with and on the machine, that is indicated 
by the following symbols: 

 

 

 

 

Indicates that protective gloves must be worn for subsequent tasks. 

 

 

 

 

Indicates that protective goggles must be worn for subsequent tasks. 

 

 

 

 

Indicates that safety shoes must be worn for subsequent tasks. 

 

 

 

 

 

 

2

 

General notices and information about environmental protection are marked by these symbols: 

 

 

 

NOTE 

Refers to further information and useful notes. 

 

 

 

ENVIRONMENTAL PROTECTION 

Refers to measures to be observed to prevent damage to the environment. 

 

 
 

3

 

Safety notes are introduced by these symbols and words: 

 

 

 

CAUTION 

Refers to a dangerous situation in which failure to comply with the safety note could result in light injuries. 

 

 

 

WARNING 

Refers to a dangerous situation in which failure to comply with the safety note could result in death or serious 
injuries. 

 

 

 

DANGER 

Refers to an (extremely) dangerous situation in which failure to comply with the safety note will result in 
death or serious injuries. 

Summary of Contents for FX116














































Reviews:

No comments

Brands by name

Popular brands

Load more brands