VMI VIBER X3, Manual, Page: 16 / 60

Vibraon Measurement Instruments
14
7 Warning messages
The following message may appear in normal operation:






Warning messages
The following message may appear in normal operation:
This message may appear if the calibration data is lost from the permanent FRAM memory or if the calibration data are
corrupted.
In such cases, the instrument must be re-calibrated; otherwise it will measure incorrectly. The message appears only
once, and then default calibration data is used.
When this message appears, the battery voltage is too low to ensure a correct running condition. The measurements may
be invalid! The instrument battery pack must be charged immediately, using the external charger. In order to temporarily
decrease the power consumption, the backlight will be switched
OFF . The instrument can still work, but only for a short
while. If even in this condition the voltage remains low, the instrument will shut off in 20 sec.
This message appears only if the Auto-shut off setting is enabled. The user may cancel the shut-off condition, pressing any
key except ON/OFF . If no key is pressed the instrument will shut off in 5 seconds.
This message appears only if the
Transducer power setting
is enabled and indicates that the
transducer is missing or is out of order.
When the
Transducer power setting is disabled, the user has the possibility to use another external source for the vibration input (a signal
generator or a buffered output from another device).
When the instrument starts, the
Transducer power setting is always ENABLED . When this message appears, it will remain on the screen, even
if the transducer is plugged-in. To continue the normal running mode in such a condition, switch the screen temporarily to another menu.
When you come back, the message disappears.
2 Battery status bar
In every measurement screen, at the upper side, a battery status bar is shown.
The status bar indicates the battery voltage, as follows:
External charger plugged into the instrument. Battery is charging.
If the charger is removed, the status bar shows the remaining battery voltage:
When the voltage exceeds 4.0 V, the battery status bar indicates full battery.
If the battery voltage drops to less than 3.5 V, the instrument will shut-off in 20 sec.
Lift the battery cover by removing the two screws on the back side of the instrument.









Warning messages
The following message may appear in normal operation:
This message may appear if the calibration data is lost from the permanent FRAM memory or if the calibration data are
corrupted.
In such cases, the instrument must be re-calibrated; otherwise it will measure incorrectly. The message appears only
once, and then default calibration data is used.
When this message appears, the battery voltage is too low to ensure a correct running condition. The measurements may
be invalid! The instrument battery pack must be charged immediately, using the external charger. In order to temporarily
decrease the power consumption, the backlight will be switched
OFF
. The instrument can still work, but only for a short
while. If even in this condition the voltage remains low, the instrument will shut off in 20 sec.
This message appears only if the Auto-shut off setting is enabled. The user may cancel the shut-off condition, pressing any
key except ON/OFF . If no key is pressed the instrument will shut off in 5 seconds.
This message appears only if the Transducer power setting is enabled and indicates that the
transducer is missing or is out of order.
When the
Transducer power setting is disabled, the user has the possibility to use another external source for the vibration input (a signal
generator or a buffered output from another device).
When the instrument starts, the
Transducer power setting is always ENABLED . When this message appears, it will remain on the screen, even
if the transducer is plugged-in. To continue the normal running mode in such a condition, switch the screen temporarily to another menu.
When you come back, the message disappears.
2 Battery status bar
In every measurement screen, at the upper side, a battery status bar is shown.
The status bar indicates the battery voltage, as follows:
External charger plugged into the instrument. Battery is charging.
If the charger is removed, the status bar shows the remaining battery voltage:
When the voltage exceeds 4.0 V, the battery status bar indicates full battery.
If the battery voltage drops to less than 3.5 V, the instrument will shut-off in 20 sec.
Lift the battery cover by removing the two screws on the back side of the instrument.



This message may appear if the calibration data is lost
from the permanent FRAM memory or if the calibration
data are corrupted. In such cases, the instrument must be
re-calibrated; otherwise it will measure incorrectly. The
message appears only once, and then default calibration
data is used.
When this message appears, the battery voltage is too
low to ensure a correct running condition. The measure-
ments may be invalid! The instrument battery pack must
be charged immediately, using the external charger. In or-
der to temporarily decrease the power consumption, the
backlight will be switched OFF. The instrument can still
work, but only for a short while. If even in this condition
the voltage remains low, the instrument will shut off in 20
sec. Battery charge should not be terminated before the
green LED light has gone out.
This message appears only if the Auto-shut off setting
is enabled. The user may cancel the shut-off condition,
pressing any key except ON/OFF. If no key is pressed the
instrument will shut off in 5 seconds.
This message appears only if you have forgot to connect
the transducer, or if transducer is broken.
When the Transducer power setting is disabled, the user has the possibility
to use another external source for the vibration input (a signal generator or a
buffered output from another device).
When the instrument starts, the Transducer power setting is always ENAB
-
LED. When this message appears, it will remain on the screen, even if the
transducer is plugged-in. To continue the normal running mode in such a
condition, switch the screen temporarily to another menu.
When you come back, the message disappears.






Warning messages
The following message may appear in normal operation:
This message may appear if the calibration data is lost from the permanent FRAM memory or if the calibration data are
corrupted.
In such cases, the instrument must be re-calibrated; otherwise it will measure incorrectly. The message appears only
once, and then default calibration data is used.
When this message appears, the battery voltage is too low to ensure a correct running condition. The measurements may
be invalid! The instrument battery pack must be charged immediately, using the external charger. In order to temporarily
decrease the power consumption, the backlight will be switched
OFF . The instrument can still work, but only for a short
while. If even in this condition the voltage remains low, the instrument will shut off in 20 sec.
This message appears only if the Auto-shut off setting is enabled. The user may cancel the shut-off condition, pressing any
key except ON/OFF . If no key is pressed the instrument will shut off in 5 seconds.
This message appears only if the Transducer power
setting
is enabled and indicates that the
transducer is missing or is out of order.
When the
Transducer power setting is disabled, the user has the possibility to use another external source for the vibration input (a signal
generator or a buffered output from another device).
When the instrument starts, the
Transducer power setting is always ENABLED . When this message appears, it will remain on the screen, even
if the transducer is plugged-in. To continue the normal running mode in such a condition, switch the screen temporarily to another menu.
When you come back, the message disappears.
2 Battery status bar
In every measurement screen, at the upper side, a battery status bar is shown.
The status bar indicates the battery voltage, as follows:
External charger plugged into the instrument. Battery is charging.
If the charger is removed, the status bar shows the remaining battery voltage:
When the voltage exceeds 4.0 V, the battery status bar indicates full battery.
If the battery voltage drops to less than 3.5 V, the instrument will shut-off in 20 sec.
Lift the battery cover by removing the two screws on the back side of the instrument.









Warning messages
The following message may appear in normal operation:
This message may appear if the calibration data is lost from the permanent FRAM memory or if the calibration data are
corrupted.
In such cases, the instrument must be re-calibrated; otherwise it will measure incorrectly. The message appears only
once, and then default calibration data is used.
When this message appears, the battery voltage is too low to ensure a correct running condition. The measurements may
be invalid! The instrument battery pack must be charged immediately, using the external charger. In order to temporarily
decrease the power consumption, the backlight will be switched
OFF . The instrument can still work, but only for a short
while. If even in this condition the voltage remains low, the instrument will shut off in 20 sec.
This message appears only if the
Auto-shut off
setting is enabled. The user may cancel the shut-off condition, pressing any
key except ON/OFF . If no key is pressed the instrument will shut off in 5 seconds.
This message appears only if the Transducer power setting is enabled and indicates that the
transducer is missing or is out of order.
When the
Transducer power setting is disabled, the user has the possibility to use another external source for the vibration input (a signal
generator or a buffered output from another device).
When the instrument starts, the
Transducer power setting is always
ENABLED
. When this message appears, it will remain on the screen, even
if the transducer is plugged-in. To continue the normal running mode in such a condition, switch the screen temporarily to another menu.
When you come back, the message disappears.
2 Battery status bar
In every measurement screen, at the upper side, a battery status bar is shown.
The status bar indicates the battery voltage, as follows:
External charger plugged into the instrument. Battery is charging.
If the charger is removed, the status bar shows the remaining battery voltage:
When the voltage exceeds 4.0 V, the battery status bar indicates full battery.
If the battery voltage drops to less than 3.5 V, the instrument will shut-off in 20 sec.
Lift the battery cover by removing the two screws on the back side of the instrument.


