background image

VZN T5 SERIES

9

P/N 1011066 Rev. G 12/13 

INSTALLATION

Unpacking

  1.  Open the large box. It should contain:

A. Plate-mounted VZN system with Ultra Filter 

Cartridge installed

B. Padded envelope containing:

•  Power Adaptor
•  Adaptor Plugs
•  Owner’s Manual
•  Mounting Bracket
•  Filter Wrench
•  Glove and Sticker Kit
•  Sanitizing Tee Fitting and Plug

C. Carbon Element and Carbon Element Housing

  3.  Remove all packing materials and protective coverings 

from the system.

  4.  Remove the information packet. Fill out and mail the  

warranty card immediately to prevent any delay in 

obtaining warranty coverage. 

NOTE: If any parts are damaged, contact A.J. Antunes & 

Co. IMMEDIATELY at 1-800-253-2991 (toll free in the U.S. 

and Canada) or 1-630-784-1000.

Equipment Setup

GENERAL

When placing the system into service, pay attention to the  

following guidelines:
 

•  Do NOT immerse cord or plug in water.

 

•  Keep cord away from heated surfaces.

ELECTRICAL

The line voltage must match the voltage on the specification 

label. The plug on the power cord must match the appropriate 

outlet. Do NOT connect the system to a switched electrical 

outlet.

PLUMBING
NOTE: The system must be connected to the COLD water 

line. Do NOT connect the system to the hot water line. 

The VZN system uses the following connections:

System Inlet

3/4" NPT

System Outlet  

(Product Water)

3/4" NPT

Drain

3/4" FNPT

Rinse Outlet

3/4" (Garden Hose or 3/4" ID Hose)

When making a plumbing connection to the system, use a 

back-up wrench on the supporting plumbing. Always use a 

quality, approved pipe sealant or thread seal tape on pipe 

threads. Do NOT allow pipe sealant inside pipes.
Do NOT over tighten the connections. Use plastic fittings 

when connecting to the plastic connections of the system. 

If soldered plumbing is used, do NOT apply heat to, or near, 

the filtration system. Use union (O-ring seal) connections for 

ease of installation and future servicing.

SUGGESTED TOOLS AND SUPPLIES FOR INSTALLATION

The following tools and supplies are suggested to help with 

the installation:

• Screwdriver

• Adjustable Wrenches

• Drill with Bits

• Level

• Tape Measure

• Pipe Dope or Thread Seal Tape

• Two Gallon Bucket

• Fresh, Unscented Liquid Chlorine 

Bleach

• Pipe Wrenches

• Garden Hose (for rinsing)
• Hose or pipe for drain line

Summary of Contents for VZN-421H-T5

























Reviews: