manualshive.com logo in svg

Vivotek Supreme IP9165-LPR, User Manual

The Vivotek Supreme IP9165-LPR is a high-performance license plate recognition camera. To learn more about its features and functionality, download the free user manual from our website. Stay informed and optimize your security system with the comprehensive manual available for download.

Share
Download
background image

VIVOTEK

 

356 - User's Manual

8.32 Connect to AP 

(capability_network_wireless > 0)

Note:

 This request requires Administrator privileges. 

Method:

 GET/POST 

Syntax: 

http://

<servername>

/cgi-bin/admin/connect_ap.cgi 

PARAMETER 

VALUE 

DESCRIPTION 

N/A 

N/A 

Apply the wireless settings and connect to AP. 

8.33 Get wireless information 

(capability_network_wireless > 0)

Note:

 This request requires Administrator privileges. 

Method:

 GET/POST 

Syntax: 

http://

<servername>

/cgi-bin/admin/getwirelessinfo.cgi 

PARAMETER 

VALUE 

DESCRIPTION 

N/A 

N/A 

Get wireless information. Camera will return following information. 
1. Wireless channel 
2. Link quality 
3. Signal level 
4. Noise level 
5. SNR 
6. TX Rate 
7. RX Rate 

Summary of Contents for Supreme IP9165-LPR
























































































































































































































































































































































































Reviews:

No comments

Related manuals for Supreme IP9165-LPR

Eaton PH1 Technical Manual preview
PH1
Brand: Eaton Pages: 32
Observint T5 Quick Installation Manual preview
T5
Brand: Observint Pages: 2
Panasonic BL-C1A - Network Camera Troubleshooting Manual preview
BL-C1A - Network Camera
Brand: Panasonic Pages: 19
Panasonic i-Pro WV-SP102 Datasheet preview
i-Pro WV-SP102
Brand: Panasonic Pages: 2
Panasonic i-Pro WV-SP306 Installation Manual preview
i-Pro WV-SP306
Brand: Panasonic Pages: 36
SAA Asia Limited SND-7080 Quick Manual preview
SND-7080
Brand: SAA Asia Limited Pages: 76
FALEEMI FSC880 User Manual For Mac preview
FSC880
Brand: FALEEMI Pages: 14
Federal Signal Corporation Split Vision VSLR3 Installation Instructions preview
Split Vision VSLR3
Brand: Federal Signal Corporation Pages: 4
Halma BEA LZR-WIDESCAN Manual preview
BEA LZR-WIDESCAN
Brand: Halma Pages: 20
S/C Black BLK-IPS101 User Manual preview
BLK-IPS101
Brand: S/C Black Pages: 34
Ubiquiti airCam MINI User Manual preview
airCam MINI
Brand: Ubiquiti Pages: 31
Unisto e-Guard Manual preview
e-Guard
Brand: Unisto Pages: 2
Red Arrow SMAC-2 Installation Instructions Manual preview
SMAC-2
Brand: Red Arrow Pages: 2
Steren HER-257 Instruction Manual preview
HER-257
Brand: Steren Pages: 39
Q-See QSDR744KRTS Quick Installation Manual preview
QSDR744KRTS
Brand: Q-See Pages: 9
CommBox ZTP0015 Instruction Manual preview
ZTP0015
Brand: CommBox Pages: 4
Solar Plus Ajax CombiProtect Quick Start Manual preview
Plus Ajax CombiProtect
Brand: Solar Pages: 2
Q-See QT428-811 Quick Installation Manual preview
QT428-811
Brand: Q-See Pages: 13

Brands by name

Popular brands

Load more brands