Vivotek IZ9361-EH User Manual Download

Page: 163 / 332

VIVOTEK

User's Manual - 163

"capability_image_c<n>_exposure_
modetype")

Gain.

"irispriority"

: Adjust with variable

Iris, auto Gain and Shutter speed.

"manual"

: Adjust with variable

Shutter, Iris and Gain.

* We support this parameter when the
version number (httpversion) is equal
or greater than 0302a.

irismode

fixed, indoor, outdoor

4/4

Control DC-Iris mode.

"outdoor"

: Auto-setting DC-Iris to

get best quality, but easy to meet
rolling or flicker effect in indoor
environment.

"indoor"

: Avoid rolling and flicker

effect first.

"fixed"

: Open the iris to maximum.

* Only available when
"capability_image_c<n>_iristype"=dc
iris

piris_mode

manual, indoor, outdoor,-

1/4

Control P-Iris mode.

"outdoor"

: Auto-setting P-Iris to get

best quality, but easy to meet rolling or
flicker effect in indoor environment.

"indoor"

: Avoid rolling and flicker

effect first.

"manual"

: Manual set P-Iris by

"piris_position".

"-"

: not support. (only available when

"capability_image_c<0~(n-1)>_sens
ortype" is "smartsensor")
* Only available when
"capability_image_c<n>_iristype"=pi
ris

piris_position

1~100

1/4

Manual set P-Iris.
1: Open <-> 100: Close

* Only valid when
"piris_mode"=manual or
"capability_image_c<0~(n-1)>_sens

Summary of Contents for IZ9361-EH













































































































































































































































































































































Search results

Summary of Contents for IZ9361-EH

Reviews:

Related manuals for IZ9361-EH

Brands by name

Popular brands

Vivotek IZ9361-EH, User Manual

Search results

Summary of Contents for IZ9361-EH

Reviews:

Related manuals for IZ9361-EH

Brands by name

Popular brands