vividtouch VTE-8400 Installation & Operation Manual Download Page 42

Page: 42 / 69

Audio Menu

This menu is used for adjusting volume settings.

Volume

Adjust the sound. Press





to select the desired level, and then press

ENTER

Range: 0~100

Default:

Treble

Adjust the sound in high tones (treble). Press





to select the desired level, and

then press

ENTER

Range: -6~6

Default:

Bass

Adjust the sound in low tones (bass). Press





to select the desired level, and

then press

ENTER

Range: -6~6

Default:

Balance

Adjust the balance of the left and right speakers. Press





to select the desired

level, and then press

ENTER

Range: -6~6

Default:

Internal Speaker

Turn the internal speaker on or off

Default:

Audio Source

Select the audio source for the Main input

Options: DisplayPort, HDMI1, HDMI2, HDMI3, HDMI4, Line-In

Default:

Line-in

Summary of Contents for VTE-8400






































































Search results

Summary of Contents for VTE-8400

Reviews:

Related manuals for VTE-8400

Brands by name

Popular brands

vividtouch VTE-8400, Installation & Operation Manual

Search results

Summary of Contents for VTE-8400

Reviews:

Related manuals for VTE-8400

Brands by name

Popular brands