vividtouch VTE-8400 Installation & Operation Manual Download Page 4 | Manualshive

Page: 4 / 69

background image

4

Compliance Information

VIVIDtouch hereby declares that the Product's Model Number:

VTE-8400

Conforms with the provisions of:

•

FCC: FCC CFR Title 47 Part 15 Subpart B Class A, CISPR 22:2008

•

ICES-003 Issue 5: 2012 Class A (For Canada )

•

CE: EN 55022: 2010 + AC: 2011

•

EN 55024: 2010

•

EN 61000-3-2: 2006 + A2: 2009

•

EN 61000-3-3: 2008

•

cTUVus: UL 60950-1:2007

•

CB: IEC 60950-1: 2005 + A1

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

DECLARATION OF CONFORMITY:

FCC PART 15:

«
...
2
3
4
5
6
...
»

Summary of Contents for VTE-8400






































































Reviews:

No comments

Related manuals for VTE-8400

Brand: Tatung Pages: 27

Brand: Elo TouchSystems Pages: 37

Brand: BIOS Diagnostics Pages: 20

grass valley MV-831

Brand: Belden Pages: 2

Brand: Omron Pages: 16

6656HG2 - T 560 - 15" LCD Monitor

Brand: IBM Pages: 34

Brand: Startax Pages: 31

Nixie Ornament Z580M / IN-19

Brand: Mr. Nixie Pages: 2

Brand: AOC Pages: 33

Brand: FDS Pages: 14

Brand: Westinghouse Pages: 31

Brand: Quanmax Pages: 37

Brand: ARTHUR HOLM Pages: 16

Brand: Fujitsu Pages: 39

Brand: Fujitsu Pages: 2

Brand: Fujitsu Pages: 2

Brand: Fujitsu Pages: 50

Brand: Fujitsu Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands