manualshive.com logo in svg

Vitesse VSC8228, Usage Manual, Page: 8 / 13

Share
Download
Vitesse VSC8228 Usage Manual Download Page 8

VSC8228 Evaluation Board 

  

Software / User Usage Guide 

Applications Engineering 

____________________________________________________________________________

 

 

 

________________________________________________  

8 of 13

 _______________________________________________ 

Rev 1.0

 

Confidential

 

 

 

01/25/05

 

 

 
After the program has finished installing, you will find a “

VSCControlSoftware”

 shortcut on the Windows  

program menu as shown below. 
 

 

 

2.  If the above method is not successful then try the following: 

Insert the CD, go to “

My Computer,

” and right click on your compact disk drive icon

.

  Select “

Open

” and 

a Windows Explorer window will open. Then open the “

Software” 

folder and run “

SETUP.EXE.

”  

 

 

 

 
 
Please wait a few minutes for the software to install. 

 
After the program has finished installing, it creates a “

VSCControlSoftware”

 shortcut on the Windows 

program menu as shown above. 
 
 
 
 
 
 
 

Summary of Contents for VSC8228














Reviews:

No comments