LIMITED LIABILITY WARRANTY
VITEK products carry a three (3) year limited warranty. VITEK
warrants to the purchaser that products manufactured by VITEK
are free of any rightful claim of infringement or the like, and when
used in the manner intended, will be free of defects in materials and
workmanship for a period of three (3) years, or as otherwise stated
above, from the date of purchase by the end user. This warranty is
nontransferable and extends only to the original buyer or end user
customer of a VITEK Authorized Reseller.
The product must have been used only for its intended purpose, and
not been subjected to damage by misuse, willful or accidental damage,
caused by excessive voltage or lightning.
The product must not have been tampered with in any way or the
guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact your local VITEK Reseller should servicing become
necessary.
VITEK makes no warranty or guarantee whatsoever with respect to
products sold or purchased through unauthorized sales channels.
Warranty support is available only if product is purchased through a
VITEK Authorized Reseller.
Version 1.0
Oct. 2014
28492 CONSTELLATION ROAD
VALENCIA, CA 91355
WWW.VITEKCCTV.COM
Installation Instructions
1. Locate the mounting template at the installation position and drill the ceiling
or wall if needed.
2. Open the dome cover by loosening screws(3x12mm). Use the torque wrench
supplied.
A. Flush mount type: (See optional Dome Mounts pg.3)
- Place the dome base unit on pre-drilled position and attach using
mounting screws (4x30mm).
- Route the Ethernet & Power cable to the connecting place.
B. Surface mount type (Option): (See optional Dome Mounts pg.3)
- Place the surface mount on pre-drilled position and attach using
mounting screws (3x30mm). Assemble the cable conduit, otherwise
tighten a conduit hole cap.
- Route the Ethernet & Power cable to the connecting place.
- Affix the dome base unit to the surface mount using the assembly
screws (4x14mm). Before attaching the dome base make sure the
assembly holes are aligned with the surface mount assembly holes.
4. Set the camera’s viewing angle.
5. Replace the dome cover to the dome base unit and tighten the assembly
screws.
Installation Instructions
5
7
8
6
Assembly Screw
(4x14mm)
Torque Wrench
Assembly Screw
(4x12mm)
Mounting Screw
(4x30mm)
A
Flush mount type
B
Surface mount type
Flush Mount Installa-
tion requires a Flush
Mount Decorator Plate
(See pg. 3)
Flush Mount
Decorator Plate
Installation Instructions
Power Supply Connections
• Make sure the power is removed before installation.
• After all connections are finished properly, follow the order for applying power.
a) Plug the network cable into RJ-45 Ethernet Port at the rear panel.
If PoE is the unique power, there will be no need to connect Power terminal.
b) When DC12V or AC24V Local power is necessary, first connect the low
voltage (DC12V or AC24V), then plug the AC adapter to AC outlets to avoid an
improper reset from power spike and damage from a voltage surge with no load.
When PoE and Local power are connected, Local power has priority
Camera can work with either 24VAC or 12VDC, dual voltage power and PoE
(IEEE Std. 802.3af). Primary and secondary grounds are completely isolated
to avoid the possible ground-loop problems.
RED(~24V+)
BLACK(~24V-)
GREEN(ALM-I)
BLUE(ALM-O)
GRAY(GND)
BROWN(AU-I)
GRAY(GND)
ORANGE(AU-O)
0.2M
Junction Box Plate
Junction Box
Assembly Screw
(FM 4x8mm)
Wrench bolt
( M4x12mm)
Mounting to Junction Boxes
The Dome camera with flush mount application, pre-drilled mounting holes on.
Dome housing accommodate various junction boxes, making installation easy
and less time consuning.
