Vitek VT-2176, Manual Instruction

Page: 4 / 26

4
ENGLISH
•
Do not wind the power cord around the unit
body.
•
Check the power cord insulation integrity from
time to time.
•
If the power cord is damaged, it should be
replaced by the manufacturer, a maintenance
service or similar qualified personnel to avoid
danger.
•
Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction is
detected or after it was dropped, unplug the unit
and apply to any authorized service center from
the contact address list given in the warranty
certificate and on the website www.vitek.ru.
•
Transport the unit in the original package only.
• Keep the unit out of reach of children and dis-
abled persons.
THIS UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY. ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low tem-
perature keep it for at least three hours at room
temperature.
ATTENTION! The convention fan heater is intended
only for additional heating of rooms. It is not meant
for operation as main heating unit.
•
Unpack the unit.
• Check the unit for damages, do not use it in case
of damages.
• Make sure that the unit operating voltage corre-
sponds to the voltage of your mains.
• Make sure that the operation mode switch (4) is
set to the position «
0 » (the unit is switched off).
SETTING
Stand mode
•
Turn the unit over.
• Insert the supporting plates with wheels (1) into
the openings on the convection fan heater body.
• Turn the unit over and set it on the wheels.
USING THE FAN HEATER
•
Before switching the unit on, make sure that
your home mains voltage corresponds to the
unit operating voltage, and the switch (4) is in
the position «
0 » (the unit is switched off).
•
Insert the power plug into the mains socket.
• Set the operation mode switch (4) into the nec-
essary position:
–
0 – the fan heater is switched off,
–
I – minimum heating power (800 W),
–
II – maximum heating power (1600 W).
•
To dry small items, install the bracket (3) on the
convection fan heater body (5).
Notes: - do not hang wet clothes, large towels etc.
on the bracket (3).
•
To switch the unit off, set the switch (4) to the
position «
0 », then unplug the unit.
Notes:
–
While the first switching on the heating element
burns, therefore occurrence of a small amount
of smoke or foreign smell is possible. It is normal.
–
Do not open windows and doors when the unit is
operating; otherwise you will not get the desired
results, due to cold air inflow.
WARNING! Do not cover the heater to avoid
overheating.
Auto switch off functions
• The unit is equipped with an automatic switch
that switches the unit off when it is dropped or
considerably tilted. When the unit is back in the
vertical position, it will be switched on.
• If the unit is not switched on, it may mean that
there are damages in the convection fan heater.
In this case contact an authorized service center
to repair the unit.
CLEANING AND CARE
• Before cleaning disconnect the unit from the
mains and let it cool down.
• Clean the unit regularly to avoid dust accumu-
lation.
• Wipe the outer surface of the unit (5) with a
damp cloth and then wipe the fan heater dry. Do
not use any abrasives or solvents to remove dirt.
•
Do not immerse the fan heater body, the power
cord or the plug into water or any other liquids.
Provide that water does not get into the fan
heater body to avoid electric shock.
•
To clean the grids (2) of the unit, use a vacuum
cleaner with a corresponding attachment.
STORAGE
•
After cleaning put the fan heater to a dark, dry
and cool place away from children for storage.
•
Before using the fan heater next time, it is rec-
ommended to check the unit operability and
integrity of the power cord isolation and the
power cord plug.
•
Keep the unit out of reach of children and dis-
abled persons.
DELIVERY SET
Convection fan heater – 1 pc.
Support plates with wheels – 2 pcs.
Bracket for drying – 1 pc.
Instruction manual – 1 pc.
IM VT-2176.indd 4 6/11/20 10:54 AM