7
ENGLISH
If you need an extension cord use only a 3-wired extension cord with a grounding contact on the plug
and the socket.
- Marking of the cord wire section of the microwave oven and on the cable of the extension cord
should match.
- The power cable of the extension cord should not hang over the edges of the table, where children
can pull it and it should not be in a passing way.
Setting
Make sure that all packing materials are removed from the oven.
•
Do not remove a light-gray mica base inside the operating chamber in the place of microwaves
•
output (6), as it serves to protect the magnetron.
ATTENTION!
Make sure that the unit does not have damages such as: bent or broken door, broken
or loose hinges and latches, dimples inside the oven or on the door. With the existence of any of the
damages, usage of the unit is prohibited.
Set the unit on the flat stable surface that will bear its weight and max. weight of the products,
•
which will be cooked in it. Place the unit out of the reach of children.
Do not place the unit in places with high moisture and temperature, and near inflammable ob-
•
jects.
Proper ventilation is needed for normal operation of the unit.
•
Set the oven leaving at least 7-8 cm of space behind and on the sides of the oven and 30 cm of
•
space above the oven. Do not close and do not block ventilation openings on the microwave oven
case. Do not remove supporting legs from the bottom of the oven.
Do not use the unit without the glass tray and the roller ring.
•
Make sure that the power cable does not have any damages and does not pass below the unit or
•
through any hot or sharp surfaces.
Microwave oven assembly
Remove the package and the accessories from the operating chamber. Check the oven whether
there is deformation or not. Pay special attention to the door state. If there is some problem do not
set and do not switch on the oven.
Protective covering
Case:
If there is protective covering, remove it from the surface.
Do not remove light grey mica plate inside the operating chamber at the place of microwaves
output (6); it serves to protect the magnetron.
Setting the glass tray
Set the rotating tray support (4) in the opening situated on the bottom of the operating chamber.
•
Set the rotating roller ring (5) on the bottom of the operating chamber.
•
Carefully set glass tray (3) on the roller ring (5), by matching ledges and grooves of the support
•
(4).
Never set the glass tray with its bottom upside down.
•
Do not prevent rotation of the glass tray while operating the oven.
•
During cooking always use the glass tray and the tray support.
•
Cookware should be always set only on the glass tray.
•
The glass tray can rotate clockwise/anti clockwise. It is normal.
•
If cracks or chops appear, stop using the unit immediately or replace the glass tray.
•
Operation
Before switching on the unit, make sure that the voltage in your home socket corresponds
•
to the
voltage specified on the unit.
VT-1690 BELORUS.indd 7
VT-1690 BELORUS.indd 7
11.08.2011 18:55:30
11.08.2011 18:55:30
Summary of Contents for VT-1690
