Vitek VT-1508, Manual Instruction, Page: 5 / 36

5
ENGLISH
•
Remove the tray grid (6), remove the tray and
pour the water out of it, install the tray and the
grid (6) back to their places.
•
The coffee maker is ready for operation.
MAKING ESPRESSO
•
Remove the water tank (2), fill it with cold
water up to the “MAX” mark and install it back
to its place. Make sure that the water level in
the tank (2) is not below the mark «MIN», reg-
ularly add water to the tank (2).
•
Put ground coffee in the filter (15) using the
measuring spoon (16), slightly tamp the
coffee with the back side of the measuring
spoon (16).
•
Install the filter holder (7) back to its installa-
tion place. The filter holder (7) ledges should
match the groves on the boiler “
”, after that
turn the filter holder (7) handle to the utmost
right position «
».
•
Place the cup on the tray grid (6).
•
Insert the power plug into the mains socket.
•
Switch the coffee maker on by pressing the
button (13) “
”, you will hear a sound sig-
nal, the light indicator will light up blue and
start flashing.
•
Wait until water in the boiler heats up, the light
indicator will be glowing constantly.
Notes: - warm the cups that you want to use
first; to do this, place the cups on the cup warm-
ing tray (14), while water is heated in the boiler,
the tray (14) heats up too, thus warming the
cups.
–
To make one cup of espresso press the but-
ton (12) «
», the pump will switch on for
3 seconds for preliminary soaking of coffee;
after a pause the pump will be switched on
and operate for 15 seconds, before the water
supply stops you will hear sound signals.
–
To make two cups of espresso press the
button (11) «
», in this case set one big or
two small cups on the grid (6). When you
press the button (11), the pump will switch
on for 3 seconds for preliminary soaking
of coffee; after a pause the pump will be
switched on and operate for 30 seconds,
before the water supply stops you will hear
sound signals.
–
For manual coffee making press the water
supply button (10) «
», the pump will switch
on for 3 seconds; after a pause the pump will
be switched on and the water will be supplied
constantly. After the cup is filled with ready
coffee, switch the water supply off again by
pressing the button (10) “
”.
Notes:
–
if you need to switch the water supply off dur-
ing the espresso making, press the button
(11 “
” or 12 “ ”) again;
–
successive making of coffee should be per-
formed with 2-3 min intervals;
–
control the tray (6) filling, periodically pour out
the liquid and wash the tray (6). A red pop-
up indicator in the center of the tray (6) grid
shows the tray (6) filling.
•
Switch the coffee maker off by pressing the
button (13) «
».
•
Wait until the coffee maker cools down and
remove the filter holder (7), turning the
holder (7) handle to the utmost left position
“
”. Remove the ground coffee remnants and
wash the filter (15). For easy removing of the
coffee remnants use the retainer (8) to prevent
the filter (15) from falling off the holder (7).
MAKING CAPPUCCINO
ATTENTION! Be careful not to get burns by
the outgoing steam from the cappuccinator
pipe (4) and the removable tip (5).
•
Make coffee, as described in the chapter
«MAKING ESPRESSO», in the warm cup with
enough capacity to add frothed milk.
Notes:
–
it is recommended to make the necessary
amount of espresso before frothing the milk,
because the water temperature in the steam
supply mode is higher than temperature of
water intended for making espresso, so the
ready drink may taste different;
–
it is recommended to make the next cup of
espresso in 5-10 minutes after frothing the milk;
–
you can reduce the time of the water tem-
perature decreasing, to do that place a cup
under the filter holder (7) (do not add ground
coffee to the filter (15) and switch the manual
water supply on by pressing the button (10)
«
», after the cup is filled press the button
(10) again to switch the water supply off.
•
Press the steam supply button (9) “ ”, the
light indicator will light up red and start flash-
ing. Wait until the light indicator stops flashing
and glows constantly.
•
Place a suitable cup under the tip (5), care-
fully turn the steam supply control knob (3)
«OFF--- +» and drain the remaining water and
condensed moisture from the cappuccinator
IM VT-1508.indd 5 28.05.2019 14:43:54