Vitek 113621, Manual Instruction

Page: 6 / 32

6
ENGLISH
off and the actual room humidity indica-
tions (22) will appear on the display.
–
If you need to check the preset humidity value,
press/touch the button (24) once, the preset
humidity indications (22) will appear on the
display and flash 5 times, and then the actual
humidity indications (22) will be shown.
Note: the room humidity level measurements
are taken every 15 minutes.
Timer setting button (25)
–
Consequently press/touch the button (25)
to set up the timer within the range from 1 to
12 hours with 1 hour step which will be shown
on the display with the symbols (19).
–
When the set time is reached the unit will be
switched off.
–
To switch the timer off press/touch the but-
ton (25) until the symbols (19) go out.
Low water level indication
–
When the water tank (2) is empty, the unit will
be switched off, there will be sound signals,
and the empty water tank symbol (21) will light
up red on the display.
–
Switch the unit off with the button (16),
remove the nozzle (3), turn the clamp han-
dle (12) counterclockwise and remove the
water tank (2).
–
Fill the tank (2) with water (see the chapter
«USING THE AIR HUMIDIFIER»).
–
First place the filled water tank (2) back to
its place and then install the nozzle (3), fix
the tank (2) by turning the clamp handle (12)
clockwise until bumping.
–
Switch the unit on for further operation.
CLEANING AND CARE
WARNING! Always switch the unit off and
unplug it before cleaning.
Hard water causes appearance of mineral scale
in the process chamber (9) and in the water
tank (2) that leads to improper operation of the
unit. To avoid it:
–
use filtered, boiled and settled water. If tap
water is hard, it is recommended to mix tap
water with distilled water in proportion 1:1. If
tap water is too hard, mix it with distilled water
in proportion 1:2 or use distilled water only.
–
Change water in the water tank (2) twice a week.
–
Thoroughly wash the process chamber (9)
and the water tank (2) with neutral detergent
solution twice a week.
–
Before cleaning the process chamber (9)
remove the heating element protective lid.
–
To clean the sprayer add 5-10 drops of
detergent on it and wait for approximately
10-15 minutes. Remove the scale from the
sprayer surface with a soft brush, and then
wash the process chamber (9) with neutral
detergent solution.
–
Rinse the process chamber (9) and the water
tank (2) several times. Wipe the process
chamber (9) with a soft cloth.
–
Clean the air humidifier body (13) with a soft,
slightly damp cloth, and then wipe it dry.
–
As the humidity sensor (10) openings become
dirty, clean the sensor (10) body with a dry
cloth or a suitable brush.
Notes:
–
do not immerse the air humidifier body (13)
into water or other liquids;
–
do not use abrasive substances and sol-
vents to clean «sprayer» and the air humidi-
fier body (13).
–
as a cleaning agent for the «sprayer» you can
use a descaling agent for kettles, strictly fol-
lowing the instruction for this substance.
STORAGE
–
Pour the water out of the tank and make sure
that the process chamber and the «sprayer»
are dry before taking the unit away for storage.
–
Do not keep the unit with water inside the tank
or the process chamber.
–
Keep the air humidifier away from children in
a dry cool place.
TROUBLESHOOTING
Malfunction Possible causes Troubleshooting
No “mist” The unit is connected
improperly Check if the power plug is inserted into the mains
socket.
The unit is off Switch the unit on by pressing the button (16).
Water tank is empty or there
isn’t enough water in the tank. Fill the water tank with enough water.
IM VT-2336.indd 6 28.12.2016 17:46:12