Vitec Multimedia MGW Ace User Manual Download Page 26

Page: 26 / 101

MGW Ace Encoder

HEVC Encoding and Streaming Appliance

User Manual, Version 2.1

The Dashboard Frame

In the dashboard frame section you can control the two encoding channels.

Description

HEVC/ H.265 channel

–

Supports 4:2:0 and 4:2:2 encoding (8/10-bit) up to

1920x1080p, using various streaming protocols.

MPEG-4/ H.264 channel

–

Supports 4:2:0 encoding up to 1920x1080p using

various streaming protocols.

Figure 4-1: The Dashboard Frame

Parameter

Display

Description

1-HEVC
2-H.264

Displays the channel number and the compression format
(fixed).

Source

HD-SDI/ HDMI/ DVI/
Composite

Displays the source type assigned to the channel.

Total Bit-
Rate

Bit-rate in Mbps

Display the total bit-rate of the channel (Video+Audio+KLV

Mstreaming protocol overhead). This value doesn’t

include additional overhead required when using ProMPEG
Forward Error Correction or Zixi

™

Error Correction.

Resolution

Video resolution

Displays the encoded (output) video resolution.

Audio

Indicates if audio has been inserted into the stream.

Status

•

Playing

•

Stopped

•

Error

Displays the status of the channel.
Hovering over an "Error" state brings up a tooltip with a
description of the error.

Summary of Contents for MGW Ace






































































































Search results

Summary of Contents for MGW Ace

Reviews:

Brands by name

Popular brands

Vitec Multimedia MGW Ace, User Manual

Search results

Summary of Contents for MGW Ace

Reviews:

Brands by name

Popular brands