background image

Ovation QS BioNatural Pipette – Adjustable Volume-Set Operator’s Guide

1 - 1

Ovation BioNatural

pipettes are the ideal ergonomic solution for liquid handling

tasks that contribute to repetitive stress injuries in today's laboratory. Ovation
pipettes increase laboratory efficiency through improved liquid handling routines,
while reducing fatigue and the effect of poor postures. 

The Ovation QS is intended for use as a liquid transfer device, capable of aspirating
and dispensing precise fluid volumes. 

This manual describes how to use and care for your Ovation pipette. As you can see
from its appearance, it is different from every pipette that you have used before,
therefore please read the instructions carefully. 

Six models of the Ovation pipette are available to cover liquid dispensing needs
ranging from 0.2µL to 1000µL.

Please activate the pipette’s warranty on the VistaLab Technologies web site –
www.vistalab.com.  The required on-line form can be found in the “service” menu.
Retain all packing materials in the event that the pipette is to be sent back to VistaLab
Technologies for calibration verification or service.

Product Description

Specifications

1

OVATION QS ADJUSTABLE VOLUME-SET PIPETTES

Volume 

Dispensing

Range

Increments

Model

(µL)

(µL)

Accuracy

Precision

Ovation QS  2µL

0.2 – 2

.002

±1.5% at 2µL

0.9% at 2µL

(1057-0002)

±2.7% at 1µL

1.8% at 1µL

±9% at 0.2µL

7.6% at 0.2µL

Ovation QS  10µL

1 – 10

.01

±1% at 10µL

0.4% at 10µL

(1057-0010)

±1.5% at 5µL

0.6% at 5µL

±2.5% at 1µL

1.2% at 1µL

Ovation QS  20µL

2 – 20

.02

±1% at 20µL

0.3% at 20µL

(1057-0020)

±1.5% at 10µL

0.5% at 10µL

±7% at 2µL

2% at 2µL

Ovation QS  100µL

10 – 100

.1

±0.8% at 100µL

0.15% at 100µL

(1057-0100)

±0.8% at 50µL

0.24% at 50µL

±3.5% at 10µL

1% at 10µL

Ovation QS  200µL

20 – 200

.2

±0.8% at 200µL

0.15% at 200µL

(1057-0200)

±0.8% at 100µL

0.25% at 100µL

±2.5% at 20µL

1% at 20µL

Ovation QS  1000µL

100 – 1000

1.0

±0.8% at 1000µL

0.15% at 1000µL

(1057-1000)

±0.8% at 500µL

0.2% at 500µL

±3% at 100µL

0.6% at 100µL

Note: Performance data is based on the use of Ovation tips from VistaLab Technologies. If using
tips from another manufacturer, the above performance claims may not be achieved.
Specifications subject to change. See www.vistalab.com for current information.

Summary of Contents for 1057-0002




















Reviews: