background image

© 2011-2016 KIRAMEK, INC.

12

System Operation

PAGER RESPONSE TO FACTORY REMOTE & 1480/1460 PROGRAM SWITCH

Operation of the 1480 using your factory remote is described on pag-

es 3-6 in the 1480/1460 Owner’s Guide, while 3rd party remote start-

ers are described on page 7.  Below you can see how the pager responds 

when the factory remote and Program Switch are used, as well as when the 

engine is remote-started (see RSCM on page 7 of the 1480/1460 Owner’s Guide).

In the first picture above showing “LOCK > ARMED,” note that the last pager 
button pressed determines the icons you see.  For example, if you last pressed 
Button-II on the pager, when you then push Lock on the factory remote, in-
stead of seeing the 

 

icon, you will see 

 .  (See the “Arming Mode Note” 

at the bottom of page 9.)

       NOTE

TRUNK RELEASE

Factory Remote

Pager LCD

TRUNK OPENED

LOCK

Factory Remote

Pager LCD

ARMED

Factory Remote

Pager LCD

DISARMED

UNLOCK

Engine Starter

Pager LCD

ENGINE RUNNING

START

STOP

LOCK

2 PUSHES

Factory Remote

1480 Program SW

SENSOR BYPASS ARMED

Pager LCD

LOCK

1 PUSH

Factory Remote

1480 Program SW

ARMED, CONF. CHIRPS OFF

Pager LCD

Summary of Contents for TR537S





























Reviews: