virtual access GW3330 User Manual Download Page 292

Page: 292 / 372

29: Configuring SNMP

_______________________________________________________________________________________________________

_____________________________________________________________________________________________________

GW3300 Series User Manual

Issue: 1.7

Page 292 of 372

Web Field/UCI/Package Option

Description

Web: Host
UCI: snmpd.trapreceiver[x].host
Opt: host

Host address. Can be either an IP address or an FQDN.

Web: Port
UCI: snmpd.trapreceiver[x].port
Opt: port

UDP port to be used for sending traps.

Range

162

Web: Version
UCI: snmpd.trapreceiver[x].version
Opt: version

SNMP version.

Web: Community
UCI: snmpd.trapreceiver[x].community
Opt: community

Community to use in trap messages for this host.

Table 103: Information table for trap receiver settings

29.2.7

Inform receiver

Inform receiver settings define a notification receiver that should be sent SNMPv2c
INFORM notifications.

Figure 145: The inform receiver settings page

Web Field/UCI/Package Option

Description

Web: Host
UCI: snmpd.informreceiver[x].host
Opt: host

Host address. Can be either an IP address or an FQDN.

Web: Port
UCI: snmpd.informreceiver[x].port
Opt: port

UDP port to be used for sending traps.

Range

162

Web: Community
UCI: snmpd.informreceiver[x].community
Opt: community

Community to use in inform messages for this host.

Table 104: Information table for trap receiver settings

29.3

Configuring SNMP using command line

The configuration files are stored on /etc/config/snmpd

29.3.1

System settings using UCI

root@VA_router:~# uci show snmpd

snmpd.system=system

snmpd.system.sysLocation=Office 123

Summary of Contents for GW3330





















































































































































































































































































































































































Search results

Summary of Contents for GW3330

Reviews:

Related manuals for GW3330

Brands by name

Popular brands

virtual access GW3330, User Manual

Search results

Summary of Contents for GW3330

Reviews:

Related manuals for GW3330

Brands by name

Popular brands