virtual access GW3330 User Manual Download Page 117

Page: 117 / 372

15: Configuring SAToP and CESoPSN

_______________________________________________________________________________________________________

_____________________________________________________________________________________________________

GW3300 Series User Manual

Issue: 1.7

Page 117 of 372

Use the information table below to configure your main settings.

Web Field/UCI/Package Option

Description

Basic settings
Web: Enable
UCI: cesopd.main.enable
Opt: enable

Enables SAToP/CESoPSN services.

Disabled.

Enabled.

Advanced settings
Web: Syslog Severity
UCI: cesopd.main.severity
Opt: log_severity

Selects the severity used for logging events for SAToP/CESoPSN

in syslog. The following levels are available:

Emergency

Alert

Critical

Error

Warning

Notice

Informational

Debug

Web: TOS Enable
UCI: cesopd.main.tos_enabled
Opt: tos_enabled

Enables the use of the TOS field in the IP header.

Disabled.

Enabled.

Web: TOS Value
UCI: cesopd.main.tos_enabled
Opt: tos_value

Note: before changing this value, consult with Virtual Access

support.

Decimal value of the TOS field in the IP

header.

Range

0-255

Blackbox settings
Web: Blackbox Enable
UCI: cesopd.main.blackbox_enabled
Opt: blackbox_enabled

Enables blackbox recordings. See section ‘cesop blackbox show’

for more information.

Disabled.

Enabled.

Web: Blackbox Hours
UCI: cesopd.main.blackbox_hours
Opt: blackbox_hours

Defines the time period contained in the

blackbox. Entries older than the specified

period will be overwritten.

Range

1-24

Web: Blackbox Samples
UCI: cesopd.main.blackbox_samples
Opt: blackbox_samples

Maximum number of instances recorded in

the blackbox. When the capacity is full the

oldest entry will be overwritten.

Range

1-24

Table 36: Information table for CESoPSN main settings

15.6

Configuring main settings using UCI

The CESoPSN configuration file is stored on /etc/config/cesopd
The main settings are stored in the cesopd section of /etc/config/cesopd. There is only
one cesopd section.

config cesopd 'main'

option log_severity '5'

option enable '1'

Summary of Contents for GW3330





















































































































































































































































































































































































Search results

Summary of Contents for GW3330

Reviews:

Related manuals for GW3330

Brands by name

Popular brands

virtual access GW3330, User Manual

Search results

Summary of Contents for GW3330

Reviews:

Related manuals for GW3330

Brands by name

Popular brands