© 2005 Directed Electronics, Inc. Vista, CA
5
55
5
2. Check voltage and fuses. Use a meter to check for voltage between the red wire in the 5-pin ribbon harness
and the black ground wire. If you have less than battery voltage, check the 3A and both 30A fuses on the
relay satellite. Also make sure that the ground wire connects to a good chassis ground point.
3. Check diagnostics. The diagnostics will tell you which shutdown is active or not connected.
■
TTh
hee rreem
mo
ottee ssttaarrtt w
wiillll aaccttiivvaattee,, b
bu
utt tth
hee ssttaarrtteerr n
neevveerr een
ng
gaag
geess..
1. Check for voltage on the purple starter wire two seconds after the remote start becomes active. If there is
voltage present, skip to Step 4. If there is not voltage present, advance to Step 2.
2. Check the 30A fuses.
3. Check diagnostics. If the gray/black wire is detecting ground upon activation, the starter will not crank.
4. Make sure the purple starter wire is connected on the starter side of the optional starter kill/anti-grind relay.
5. Does the vehicle have an immobilizer? Some immobilizer systems will not allow the vehicle to crank if active.
6. Check connections. The two red heavy gauge input wires on the relay satellite should have solid connections.
"T-taps" or "scotch locks" are not recommended for any high current heavy gauge wiring. Also, if the vehicle
has more than one 12-volt input wire, then connect one red wire to each.
■
TTh
hee vveeh
hiiccllee ssttaarrttss,, b
bu
utt iim
mm
meed
diiaatteellyy d
diieess..
1. Does the vehicle have an immobilizer? The vehicle’s immobilizer will cut the fuel and/or spark during unau-
thorized starting attempts.
2. Is the remote start programmed for voltage sense? If so, the start time may not be set high enough, or you
may have to adjust the voltage threshold in programming. Voltage sense will not work on some vehicles.
3. Check diagnostics. Sometimes a shutdown will become active during cranking or just after cranking.
■
TTh
hee vveeh
hiiccllee ssttaarrttss,, b
bu
utt tth
hee ssttaarrtteerr kkeeeep
pss rru
un
nn
niin
ng
g..
1. Is the system programmed for engine checking off or voltage sense? When programmed for either of these
features, the engine cranks for the preprogrammed crank time regardless of how long it takes for the vehicle
to actually start. Adjust to a lower cranking time.
2. Was the Tach Learn successful? The LED must light solid and bright to indicate a successful learn.
3. Make sure that there is a tach signal at the purple/white tach input wire of the remote start. If there is not
a tach signal, recheck the connection to the vehicle’s tach wire and make sure the wire is not broken or
shorted to ground leading to the remote start.
■
TTh
hee vveeh
hiiccllee w
wiillll ssttaarrtt,, b
bu
utt w
wiillll o
on
nllyy rru
un
n ffo
orr 1
10
0 sseecco
on
nd
dss..
1. Is the remote start programmed for voltage sense? Try programming the unit for low voltage reference. If this
does not work, a tach wire should be used.
2. Check diagnostics.
■
TTh
hee cclliim
maattee cco
on
nttrro
oll ssyysstteem
m d
do
oeess n
no
ott w
wo
orrkk w
wh
hiillee tth
hee u
un
niitt iiss o
op
peerraattiin
ng
g tth
hee vveeh
hiiccllee..
Either the wrong accessory wire is being energized or more than one ignition or accessory wire must be ener-
gized in order to operate the climate control system.
