manualshive.com logo in svg

Vintage Air 565701, Manual

Share
Download
Vintage Air 565701 Manual Download Page 24

24

www.vintageair.com

905701 REV B 09/18/18, PG 24 OF 34

Wiring Installation (Final)

17.
18.
19.

20.

Reinstall the battery, and connect the positive and negative terminals (See Photo 17, below).

Install the firewall cover using the OEM retaining brackets (See Photo 18, below).
Route the supplied fresh air vent cable through the OEM grommet on the firewall, and reattach the cable to 

the vent under the driver side fender (See Photos 19 & 20, below).
Install the #6 Adel clamp onto the #6 drier/evaporator A/C hose, and secure it to the inner fender OEM hole 

next to the battery using a 10-24 x 1/2" screw and 10-24 nut with star washer. Use the supplied tie wraps to 

secure the hoses (See Photo 21, below). 

Driver Side Fender

View

Connect Battery

Terminals

Firewall Cover

64112-VCB

OEM Retaining 

Brackets

Route Fresh Air 

Vent Cable through 

OEM Grommet

Firewall

#6 Adel Clamp

#6 Drier/Condenser A/C Hose

Battery

Reattach Cable

to Vent

Secure Hoses

with Tie Wraps

Photo 17

Photo 18

Photo 19

Photo 20

Photo 21

Summary of Contents for 565701



































Reviews:

No comments

Brands by name

Popular brands

Load more brands