manualshive.com logo in svg

Vintage Air 565701, Manual

Share
Download
Vintage Air 565701 Manual Download Page 2

2

www.vintageair.com

905701 REV B 09/18/18, PG 2 OF 34

Table of Contents

Cover..................................................................................................................................
Table of Contents.................................................................................................................
Packing List/Parts Disclaimer..................................................................................................
Information Page..................................................................................................................
Wiring Notice.......................................................................................................................
Engine Compartment Disassembly..........................................................................................
Engine Compartment Disassembly (Cont.)...............................................................................
Passenger Compartment Disassembly.....................................................................................
Passenger Compartment Disassembly (Cont.)..........................................................................
Passenger Compartment Disassembly (Final).........................................................................
Evaporator Pre-Installation, Evaporator Firewall Bracket Installation..........................................
Evaporator and Heater Hardline Installation............................................................................
Firewall Insulation...............................................................................................................
Defrost Duct Installation, Wiring Installation...........................................................................
A/C Duct Hose Installation, Evaporator Installation.................................................................
Evaporator Installation (Cont.), Evaporator Dash and Center Louver Bracket Installation..............
Fresh Air Cover Plate & Rubber Boot Installation, Evaporator Leveling & Fresh Air Vent Duct 

Cap Installation..................................................................................................................
Wiring Installation (Cont.)...................................................................................................
Wiring Installation (Cont.), Drain Hose Installation..................................................................
Lubricating O-rings, A/C Hose Installation..............................................................................
Heater Hose & Heater Control Valve Installation......................................................................
A/C and Heater Hose Routing...............................................................................................
Wiring Installation (Cont.)...................................................................................................
Wiring Installation (Final)....................................................................................................
Driver and Passenger Side Louver Installation........................................................................
Driver and Passenger Side Louver Installation (Cont.).............................................................
Glove Box Installation.........................................................................................................
Final Steps........................................................................................................................
Wiring Diagram..................................................................................................................
Gen IV Wiring Connection Instruction....................................................................................
Operation of Controls..........................................................................................................
Troubleshooting Guide.........................................................................................................
Troubleshooting Guide (Cont.)..............................................................................................
Packing List.......................................................................................................................

  1
  2
  3
  4
  5 
  6
  7
  8
  9
10
11
12
13
14 
15
16

17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34

Summary of Contents for 565701



































Reviews:

No comments

Brands by name

Popular brands

Load more brands