manualshive.com logo in svg

Vintage Air 565701, Manual

Share
Download
Vintage Air 565701 Manual Download Page 18

18

www.vintageair.com

905701 REV B 09/18/18, PG 18 OF 34

Wiring Installation (Cont.)

4.

5.
6.
7.
8.

Apply (2) strips of Velcro to the ECU, and cut the tie wraps holding the ECU wiring together (See Photos 4 & 

5, below). 

Plug the main wiring harness black connector into the ECU module (See Photo 6, below).

Reinstall the control panel into the dash using the (4) OEM screws (See Photo 7, below).

Plug the control panel connector into the ECU module (See Photo 8, below).
Apply (2) strips of Velcro, and mount the ECU to the right of the radio on the inner dash. 

NOTE: Make sure 

the area is clean and free of debris before applying the Velcro (See Photo 9, below). 

Photo 4

Photo 5

Photo 6

Photo 7

Photo 8

Photo 9

ECU Module

Plug Main Wiring 

Harness Connector

into ECU Module

Main

Wiring Harness

Control

Panel

Reinstall Control 

Panel into Dash

Using (4) OEM Screws

Plug Control Panel

Wiring Connector 

into ECU Module

Inner Dash 

View

Mount ECU to 

Right of Radio

Apply (2) Strips 

of Velcro to 

ECU

Cut

Tie Wraps

Summary of Contents for 565701



































Reviews:

No comments

Brands by name

Popular brands

Load more brands