Vimar ELVOX 68IA/R, Installer'S Manual

Page: 12 / 52

12 EN
MATERIALE FORNITO DI SERIE SULLE TARGHE 1300
MATERIALE NON FORNITO DI SERIE DA ORDINARE SEPARATAMENTE PER PREDISPORRE
UNA TARGA CITOFONICA
MATERIALE NON FORNITO DI SERIE DA ORDINARE SEPARATAMENTE PER PREDISPORRE
UNA TARGA VIDEOCITOFONICA
MATERIALE NON FORNITO DI SERIE DA ORDINARE SEPARATAMENTE PER PREDISPORRE
UNA TARGA DA INCASSO PARETE
MATERIALE NON FORNITO DI SERIE DA ORDINARE SEPARATAMENTE PER PREDISPORRE
UNA TARGA DA ESTERNO PARETE
M
V
+T
8
7
6
5
-
ESECUZIONE DA INCASSO PARETE ESECUZIONE DA ESTERNO PARETE
Installation of entrance panel (type 13K1), flush-mounting version
- Install the flush-mounting back box (D) on the wall with the bottom edge at
a height of approx. 1.65m from the ground
- Open the entrance panel by undoing the screw under the plate (G) and
detach the camera (B) from the frame, removing the light diffuser (h) and
the microphone (I).
- Fit the frame (C) to the flush-mounting back box (D)
- Reposition the camera in the frame and the microphone in the special
housing, refitting the plug as shown in fig.16A.
- Connect the camera to the name card lighting LED board using the two
cable harnesses (harness with red/black wire for LED power supply and
harness with two green wires for connection of a second call button, if
required) fig.16B.
- Make the connections to the installation on the removable terminal block
(L). In the case of installation for two-family video door entry systems:
- Remove the blanking module (E) fig. 17, from the back of the plate using
a screwdriver, working in sequence from bottom to top (first remove the
end section, then key 1 and finally the blanking module).
- Fit the external key (F) (supplied) to the plate by pushing it lightly into
place.
- Insert the light diffuser (h) to ensure even lighting of the name cards.
- Close the entrance panel, securing it to the frame with the aid of a screw-
driver.
ESECUZIONE DA INCASSO PARETE
ESECUZIONE DA ESTERNO PARETE
B
C
D
I
N
Fig.15
A
h
G
O
L
M
Fig.16A
MATERIALE FORNITO DI SERIE SULLE TARGHE 1300
MATERIALE NON FORNITO DI SERIE DA ORDINARE SEPARATAMENTE PER PREDISPORRE
UNA TARGA CITOFONICA
MATERIALE NON FORNITO DI SERIE DA ORDINARE SEPARATAMENTE PER PREDISPORRE
UNA TARGA VIDEOCITOFONICA
MATERIALE NON FORNITO DI SERIE DA ORDINARE SEPARATAMENTE PER PREDISPORRE
UNA TARGA DA INCASSO PARETE
MATERIALE NON FORNITO DI SERIE DA ORDINARE SEPARATAMENTE PER PREDISPORRE
UNA TARGA DA ESTERNO PARETE
M
V
+T
8
7
6
5
-
E
(
Art. R130)
(
Art. R135)
F
Fig.17
1
2
3
4
Installation of entrance panel (type 13K1), surface wall-mounting version
- Open the entrance panel by undoing the screw under the plate (G) and
detach the camera (B) from the frame, removing the light diffuser (h) and
the microphone (I).
- Install the frame (C) together with the surface wall-mounting back box (P)
on the wall with the bottom edge at a height of approx. 1.65m from the
ground.
- Reposition the camera in the frame and the microphone in the special
housing (B), refitting the plug as shown in fig. 16A.
- Connect the camera to the name card lighting LED board using the two
cable harnesses (harness with red/black wire for LED power supply and
harness with two green wires for connection of a second call button, if
required) fig.16B.
- Make the connections to the installation on the removable terminal block
(L).
In the case of installation for two-family video door entry systems:
LED Ch2
12V
Fig.16B
Red/black cable
Green/green cable