IMPORTANT SAFETY INSTRUCTIONS FOR THE INSTALLATION.
ATTENTION - THE INCORRECT INSTALLATION CAN CAUSE SERIOUS
DAMAGES.
FOLLOW ALL INSTALLATION INSTRUCTIONS.
1° - This handbook is exclusively addressed to the specialized
personnel
who knows the constructive criteria and the protection
devices against accidents for motorized gates, doors and main doors
(follow the standards and the laws in force).
2° - The installer will have to issue a handbook to the final user in accordance
with the EN 12635.
3° - Before proceeding with the installation, the installer must forecast the
risks analysis of the final automatized closing and the safety of the
identified dangerous points (Following the standards EN 12453).
4° - Before installing the motion motor, the installer must verify that the
barrier is in good mechanical conditions and that it adequately opens
and closes.
5° - The installer must install the member for the manual release at a height
inferior to 1,8 m.
6° - The installer will have to remove possible impediments to the motorized
motion of the gate (eg. door bolts, sliding bolts, door locks etc.)
7° - The installer will permanently have to put the tags warning against the
deflection on a very visible point or near possible fixed controls.
8° - The wiring harness of the different electric components external to the
operator (for example photoelectric cells, flashlights etc.) must be carried
out according to the EN 60204-1.
9° - The possible assembly of a keyboard for the manual control of the
movement must be done by positioning the keyboard so that the person
operating it does not find himself in a dangerous position; moreover, the
risk of accidental activation of the buttons must be reduced.
10° - Keep the automatism controls (push-button panel, remote control etc.)
out of the children way. Command device for operating the motor (a
switch manually closed) should be placed in area visible from the
guided site and far from moving parts. It should be placed at least at
1,5 m height.
11° - this appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and
understand the hazards involved
12° - children shall not play with the appliance
13° - cleaning and user maintenance shall not be made by children without
supervision
14° - do not allow children to play with fixed controls. Keep remote controls
away from children
15° - Fixed command devices should be installed in a well visible way.
16° - Before carrying out any installation, regulation or maintenance operation
of the system, take off the voltage by operating on the special magneto
thermic switch connected upstream.
17° - At the end of the installation, the installer will have to make sure that the
parts of the door do not encumber streets or public sidewalks.
THE VIMAR COMPANY DOES NOT ACCEPT ANY RESPONSIBILITY
for possible damages caused by the non observance during the
installation of the safety standards and of the laws in force at present.
ATTENTION - FOR THE SAFETY OF PEOPLE IT IS IMPORTANT TO
FOLLOW ALL THE INSTRUCTIONS.
KEEP THESE INSTRUCTIONS WITH CARE.
1° - If it is not forecast in the electric gearcase, install a switch of magneto
thermic type upstream, (omni polar with minimum opening of the contacts
of 3 mm) with a check of conformity to the international standards. Such
device must be protected against the accidental lockup (for example by
installing inside a locked board).
2° - For the section and the type of the cables VIMAR advices to use a cable
of H05RN-F type with 1,5 sqmm minimum section and, however, to keep
to the IEC 364 and installation standards in force in your country.
3° - Positioning of a possible couple of photoelectric cells: the radius of the
photoelectric cells must be at a height of no more than 70 cm from the
ground and at a distance not superior to 20 cm from the motion plane
of the door. Their correct working must be verified at the end of the
installation in accordance with the point D.3.2 of the EN 12453
4° - To fulfill the limits set by EN 12453, and in case the peak force exceeds
the normative limit of 400 N it is necessary to have recourse to the active
presence survey on the whole height of the door (up to max 2,5 m) - The
photocells, in this case, must be applied in accordance with the point
D.4.1 of the EN 12453.
N.B.: The earthing of the system is obligatory.
The data described in this handbook are purely a guide.
VIMAR reserves the right to change them in any moment.
Carry out the system in the respect of the standards and laws in force.
16
FRAGMA
EN
