background image

COIN

®

 QUICK 

RESPONSE UPRIGHT 

SPRINKLER VK950 

(SPECIFIC APPLICATION)

TECHNICAL DATA

 1 of 14

Form No. F_081216    21.03.06   Rev 20.3

The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058

Telephone: 269-945-9501  Technical Services: 877-384-5464  Fax: 269-818-1680  Email: [email protected]

Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com

1.  DESCRIPTION

Viking  QR COIN

®

 Sprinklers are quick response specific application sprinklers 

for combustible interstitial (concealed) spaces (i.e., between floors, as well 

as low pitch attics that meet the criteria shown in the figures in this data 

page). These upright sprinklers are designed for use in specific light hazard 

combustible, as well as non-combustible, concealed spaces requiring sprinkler 

protection. The orifice design of the Viking  QR COIN

®

 Sprinkler, with a nominal 

K-factor of 5.6 (80 metric*), allows efficient use of available water supplies for 

hydraulically designed fire protection systems. The glass bulb operating element 

and special deflector combine speed of operation and area of coverage to meet 

the crucial fire protection requirement for shallow space combustible concealed 

spaces. The Electroless Nickel PTFE (ENT) coating has been investigated for 

installation in corrosive environments and is listed/approved as indicated in the 

Approval Charts. 

FEATURES

•  In some cases COIN

®

 Sprinklers can allow the use of CPVC piping within the 

concealed spaces of applications requiring sprinkler protection in open truss 

construction of both wood and steel trusses (see Figure 3) and solid wood or 

composite wood joist with upper deck filled with non-combustible insulation 

(see Figure 5).

•  COIN

®

 Sprinklers can also be installed with steel pipe in protected areas 

constructed of solid wood joists (see Figure 7), and solid wood or composite 

wood joist with upper deck filled with non-combustible insulation (see Figure 8), 

and in unobstructed open truss construction of both wood and steel trusses 

(see Figures 9 and 10) as well as obstructed wood truss construction (see 

Figure 11). 

•  When using steel pipe, COIN

®

 Sprinklers can be applied as a dry system 

using air or gas as a supervisory medium (see Figures 7–11).

•  In certain scenarios, draft curtains are 

NOT

 required when sprinkler spacing 

meets either of the following criteria (also refer to Design Criteria): 

 

-

14' X 14' (4,3 m X 4,3 m) for solid wood joists or trusses on edge

 

-

16' X 16' (4,9 m X 4,9 m) for truss construction on face (not on edge)

For examples of trusses on face or edge see Figures 13A and 13B.

2.  LISTINGS AND APPROVALS

cULus Listed: 

Category VNIV

Refer to the Approval Chart and Design Criteria in this technical data sheet for cULus Listing requirements that must be followed. 

The COIN

®

 Sprinkler has been tested to address the proper application density for shallow concealed combustible space fire 

protection when installed in accordance with this technical data page. The COIN

®

 Sprinkler must be installed in the upright position 

as specified in the appropriate application described in Figures 3–12. The clearance from the sprinkler deflector to the roof is critical 

to operation of the sprinkler (refer to Figures 3–12). The clearances from pipe to lower ceiling for CPVC pipe is critical for protection 

of CPVC pipe. 
For open truss and joist spaces, the maximum detection area is important for proper installation. 

In certain installations, draft curtains or heat collection baffles or solid walls are 

required

 using wood or other product that 

will not allow heat to escape. In these installations, the maximum detection space shall be 

limited

 to 1000 ft

2

 (93 m

2

) or  

2000 ft

2

 (185 m

2

) for solid wood joists. The draft curtain is required to protrude down from the top deck surface as specified herein. 

Additionally, draft curtains are 

not

 required and the maximum detection space shall be 

unlimited

 for open truss construction with 

the top chord member on their face (not on edge) when sprinkler spacing is up to 16' X 16' (4,9 m X 4,9 m) and for solid wood 

joists or trusses on edge when sprinkler spacing is up to 14' X 14' (4,3 m X 4,3 m). In these cases, draft curtains are 

not required

COIN

®

 Sprinkler 

VK950

5.6K (80 metric)

Replaces Form No. F_081216 20.2

(Added new Figure 6 and 12.)

Summary of Contents for VK950



























Reviews: