background image

3

GENERAL INFORMATION

1.  WARNING:  The use of cabinets for storage above the appliance may result in a potential burn hazard.

Combustible items may ignite, metallic items may become hot and cause burns.  If a cabinet storage is to be
provided the risk can be reduced by installing a rangehood that projects horizontally a minimum of 5” (12.7 cm)
beyond the bottom of the cabinets.

2.  WARNING:  This appliance shall not be used for space heating.  This information is based on safety considerations.
3.  All openings in the wall behind the appliance and in the floor under the appliance shall be sealed.
4.  Keep appliance area clear and free from combustible materials, gasoline, and other flammable vapors.
5.  Do not obstruct the flow of combustion and ventilation air.
6.  Disconnect the electrical supply to the appliance before servicing.
7.  When removing oven for cleaning and/or service;

A.  Shut off gas at main supply
B.  Disconnect AC power supply
C.  Disconnect gas line to the inlet pipe.
D.  Carefully remove the range by pulling outward.  CAUTION: Range is heavy; use care in handling.

8.  Electrical Requirement

Listed on Specification sheet.  Electrical installation should comply with national and local codes.

9.  Gas Manifold Pressure

Natural gas - 5.0” W.C.P.
LP/Propane - 10.0” W.C.P.

10.  Flexible Connection

If the unit is to be installed with flexible couplings and/or quick disconnect fittings, the installer must use a flexible
connector approved by national and local codes.  

11.  The misuse of oven doors (e.g. stepping, sitting, or leaning on them) can result in potential hazards and/or injuries.

WARNING!!

ELECTRICAL GROUNDING INSTRUCTIONS

This appliance must be electrically grounded in accordance with local codes or, in the absence of codes, with the
National Electrical Code, ANSI/NFPA 70-latest edition.  Installation should be made by a licensed electrician. 

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED

Burner Caps

1.  Burner caps are packed in styrofoam top pack with the grates and burner bowls.
2.  Remove grates.  Remove burner cap and place one on top of burners.  Place grate on grate support.

Legs

1.  Legs are packed in styrofoam top pack.
2.  Legs should be installed near to where the appliance is to be used, as they are not secure for long transit.  After

unpacking the range, raise it about a foot to remove the bottom shipping skid.  Keep the unit raised to permit the legs
to be screwed into our couplings and lower it gently to keep any undue strain from the legs and internal mounting
hardware.  It is strongly recommended that a pallet or lift jack be used rather than tilting.

Back Trim Accessories

Assembly and installation instructions are included with all back trim accessories.

Summary of Contents for VGWT241T













Reviews: